DatasheetQ Logo
Electronic component search and free download site. Transistors,MosFET ,Diode,Integrated circuits

K4S561632J-UC データシートの表示(PDF) - Samsung

部品番号
コンポーネント説明
メーカー
K4S561632J-UC
Samsung
Samsung Samsung
K4S561632J-UC Datasheet PDF : 15 Pages
First Prev 11 12 13 14 15
K4S560432J
K4S560832J
K4S561632J
Synchronous DRAM
15.0 AC Characteristics
(AC operating conditions unless otherwise noted)
Parameter
Symbol
CLK cycle time
CLK to valid
output delay
Output data
hold time
CLK high pulse width
CLK low pulse width
Input setup time
Input hold time
CLK to output in Low-Z
CLK to output in Hi-Z
CAS latency=3
CAS latency=2
CAS latency=3
CAS latency=2
CAS latency=3
CAS latency=2
CAS latency=3
CAS latency=2
tCC
tSAC
tOH
tCH
tCL
tSS
tSH
tSLZ
tSHZ
50 (x16 only)
Min
Max
5
1000
-
-
4.5
-
-
2
-
-
-
2
-
2
-
1.5
-
1
-
1
-
-
4.5
-
-
60(x16 only)
75
Unit
Min Max Min Max
6
7.5
1000
1000 ns
-
10
5
5.4
ns
-
6
2.5
3
ns
-
3
2.5
2.5
ns
2.5
2.5
ns
1.5
1.5
ns
1
0.8
ns
1
1
ns
5
5.4
ns
-
6
Note
1
1,2
2
3
3
3
3
2
Notes : 1. Parameters depend on programmed CAS latency.
2. If clock rising time is longer than 1ns, (tr/2-0.5)ns should be added to the parameter.
3. Assumed input rise and fall time (tr & tf) = 1ns.
If tr & tf is longer than 1ns, transient time compensation should be considered,
i.e., [(tr + tf)/2-1]ns should be added to the parameter.
4. tSS applies for address setup time, clock enable setup time. commend setup time and data setup time
tSH applies for address holde time, clock enable hold time. commend hold time and data hold time
16.0 DQ Buffer Output Drive Characteristics
Parameter
Symbol
Condition
Min
Typ
Max
Output rise time
trh
Measure in linear
region : 1.2V ~ 1.8V
1.37
4.37
Output fall time
Output rise time
Output fall time
tfh
Measure in linear
region : 1.2V ~ 1.8V
1.30
3.8
trh
Measure in linear
region : 1.2V ~ 1.8V
2.8
3.9
5.6
tfh
Measure in linear
region : 1.2V ~ 1.8V
2.0
2.9
5.0
Notes : 1. Rise time specification based on 0pF + 50 to VSS, use these values to design to.
2. Fall time specification based on 0pF + 50 to VDD, use these values to design to.
3. Measured into 50pF only, use these values to characterize to.
4. All measurements done with respect to VSS.
Unit
Volts/ns
Volts/ns
Volts/ns
Volts/ns
Notes
3
3
1,2
1,2
12 of 15
Rev. 1.22 August 2008

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]