CS61574A データシートの表示（PDF） - Cirrus Logic

部品番号

コンポーネント説明

メーカー

CS61574A

T1/E1 Line Interface

Cirrus Logic 

-XO ¶

&21),'(17,$/

CS61574A CS61575

Remote Loopback

Remote loopback is selected by taking RLOOP,

pin 26, high or by setting the RLOOP register bit

via the serial interface.

In remote loopback, the recovered clock and data

input on RTIP and RRING are sent through the

jitter attenuator and back out on the line via TTIP

and TRING. Selecting remote loopback overrides

any TAOS request (see Table 7). The recovered

incoming signals are also sent to RCLK, RPOS

and RNEG (or RDATA). Simultaneous selection

of local and remote loopback modes is not valid

(see Reset).

2,//0 4!/3 3OURCEOF

)NPUT )NPUT

$ATAFOR

3IGNAL 3IGNAL 44)042).'

3OURCEOF

#LOCKFOR

44)042).'





4$!4!

4#,+





ALLS

4#,+



8 24)022).' 24)022).'2#,+

.OTES  8$ONTCARE4HEIDENTIFIED!LL/NES3ELECT

INPUTISIGNOREDWHENTHEINDICATEDLOOPBACK

ISINEFFECT

 ,OGICINDICATESTHAT,OOPBACKOR!LL/NES

OPTIONISSELECTED

Table 7. Interaction of RLOOP with TAOS

In the Extended Hardware Mode the transmitted

data is looped before the AMI/B8ZS/HDB3 en-

coder/decoder during remote loopback so that the

transmitted signal matches the received signal,

even in the presence of received bipolar viola-

tions. Data output on RDATA is decoded,

however, if RCODE is low.

Driver Performance Monitor

To aid in early detection and easy isolation of

non-functioning links, the IC is able to monitor

transmit drive performance and report when the

driver is no longer operational. This feature can

be used to monitor either the device’s perform-

ance or the performance of a neighboring driver.

The driver performance monitor indicator is nor-

16

mally low, and goes high upon detecting a driver

failure.

The driver performance monitor consists of an ac-

tivity detector that monitors the transmitted signal

when MTIP is connected to TTIP and MRING is

connected to TRING. DPM will go high if the

absolute difference between MTIP and MRING

does not transition above or below a threshold

level within a time-out period. In the Host Mode,

DPM is available from both the register and pin

11.

Whenever more than one line interface IC resides

on the same circuit board, the effectiveness of the

driver performance monitor can be maximized by

having each IC monitor performance of a neigh-

boring IC, rather than having it monitor its own

performance. Note that a CS61574A or CS61575

can not be used to monitor a CS61574 due to out-

put stage differences.

Line Code Encoder/Decoder

In the Extended Hardware Mode, three line codes

are available: AMI, B8ZS and HDB3. The input

to the encoder is TDATA. The outputs from the

decoder are RDATA and BPV (Bipolar Violation

Strobe). The encoder and decoder are selected

using the LEN2, LEN1, LEN0, TCODE and

RCODE pins as shown in Table 8.

4#/$%

4RANSMIT

%NCODER

3ELECTION

2#/$%

2ECEIVER

$ECODER

3ELECTION

,/7

()'(

,/7

()'(

,%.





($"

":3

%NCODER %NCODER

!-)

%NCODER

($"

":3

$ECODER $ECODER

!-)

$ECODER

Table 8. Encoder/Decoder Selection

DS154F3

Share Link: