LV5680P データシートの表示（PDF） - SANYO -> Panasonic

部品番号

コンポーネント説明

メーカー

LV5680P

For Car Audio Systems Multi-Power Supply System IC

SANYO -> Panasonic 

LV5680P

HZIP15J Heat sink attachment

Heat sinks are used to lower the semiconductor device junction temperature by leading the head generated by the device to

the outer environment and dissipating that heat.

a. Unless otherwise specified, for power ICs with tabs and power ICs with attached heat sinks, solder must not be

applied to the heat sink or tabs.

b. Heat sink attachment

· Use flat-head screws to attach heat sinks.

· Use also washer to protect the package.

· Use tightening torques in the ranges 39-59Ncm(4-6kgcm) .

· If tapping screws are used, do not use screws with a diameter larger

than the holes in the semiconductor device itself.

· Do not make gap, dust, or other contaminants to get between the

semiconductor device and the tab or heat sink.

· Take care a position of via hole .

· Do not allow dirt, dust, or other contaminants to get between the

semiconductor device and the tab or heat sink.

· Verify that there are no press burrs or screw-hole burrs on the heat sink.

· Warping in heat sinks and printed circuit boards must be no more than

0.05 mm between screw holes, for either concave or convex warping.

· Twisting must be limited to under 0.05 mm.

· Heat sink and semiconductor device are mounted in parallel.

Take care of electric or compressed air drivers

· The speed of these torque wrenches should never exceed 700 rpm, and

should typically be about 400 rpm.

Binding head

machine screw

Heat sink

gap

Via hole

Countersunk head

mashine screw

c. Silicone grease

· Spread the silicone grease evenly when mounting heat sinks.

· Sanyo recommends YG-6260 (Momentive Performance Materials Japan LLC)

d. Mount

· First mount the heat sink on the semiconductor device, and then mount that assembly on the printed circuit board.

· When attaching a heat sink after mounting a semiconductor device into the printed circuit board, when tightening

up a heat sink with the screw, the mechanical stress which is impossible to the semiconductor device and the pin

doesn't hang.

e. When mounting the semiconductor device to the heat sink using jigs, etc.,

· Take care not to allow the device to ride onto the jig or positioning dowel.

· Design the jig so that no unreasonable mechanical stress is not applied to the semiconductor device.

f. Heat sink screw holes

· Be sure that chamfering and shear drop of heat sinks must not be larger than the diameter of screw head used.

· When using nuts, do not make the heat sink hole diameters larger than the diameter of the head of the screws used.

A hole diameter about 15% larger than the diameter of the screw is desirable.

· When tap screws are used, be sure that the diameter of the holes in the heat sink are not too small. A diameter about

15% smaller than the diameter of the screw is desirable.

g. There is a method to mount the semiconductor device to the heat sink by using a spring band. But this method is not

recommended because of possible displacement due to fluctuation of the spring force with time or vibration.

Caution for implementing LV5680P to a system board

The package of LV5680P is HZIP15J which has some metal exposures other than connection pins and heatsink as shown in the

diagram below. The electrical potentials of (2) and (3) are the same as those of pin 15 and pin 1, respectively. (2) (=pin 15) is the VCC

pin and (3) (=pin 1) is the ILM (regulator) output pin. When you implement the IC to the set board, make sure that the bolts and the

heatsink are out of touch from (2) and (3). If the metal exposures touch the bolts which has the same electrical potential with GND,

GND short occurs in ILM output and VCC. The exposures of (1) are connected to heatsink which has the same electrical potential with

substrate of the IC chip (GND). Therefore, (1) and GND electrical potential of the set board can connect each other.

No.A1764-12/13

Share Link: