AD5532HS データシートの表示（PDF） - Analog Devices

部品番号

コンポーネント説明

メーカー

AD5532HS

32-Channel 14-Bit DAC with High-Speed 3-Wire Serial Interface

Analog Devices 

AD5532HS

FUNCTIONAL DESCRIPTION

The AD5532HS consists of 32 DACs in a single package. A

14-bit digital word is loaded into one of the 32 DAC registers

via the serial interface. This is then converted (with gain and

offset) into an analog output voltage (VOUT0–VOUT31).

To update a DAC’s output voltage, the required DAC is

addressed via the serial port. When the 5-bit DAC address

and 14-bit DAC data have been loaded the selected DAC

converts the code.

On power-on, all the DACs are loaded with zeros.

Digital-to-Analog Section

The architecture of each DAC channel consists of a resistor-

string DAC followed by an output buffer amplifier. The voltage

at the REF_IN pin provides the reference voltage for the cor-

responding DAC. Since the input coding to the DAC is straight

binary, the ideal DAC output voltage is given by:

VDAC

= VREF _ IN

214

×D

where D = decimal equivalent of the binary code that is loaded

to the DAC register i.e., 0–16,383.

Output Buffer Stage—Gain and Offset

The function of the output buffer stage is to translate the

0 V–2.5 V output of the DAC to a wider range. This is done by

gaining up the DAC output by two and offsetting the voltage

by the voltage on OFFS_IN pin.

VOUT = (2 × VDAC ) – VOFFS _ IN

VDAC is the output of the DAC.

VOFFS_IN is the voltage at the OFFS_IN pin.

Table I shows how the output range of VOUT relates to the offset

voltage supplied by the user.

Table I. Sample Output Voltage Ranges

VOFFS_IN

(V)

0

2.5

VDAC

(V)

0 to 2.5

0 to 2.5

VOUT

(V)

0 to 5

–2.5 to +2.5

VOUT is limited only by the headroom of the output amplifiers.

VOUT must be within maximum ratings.

Reset Function

The reset function on the AD5532HS can be used to reset all

nodes on the device to their power-on-reset condition. All the

DACs are loaded with 0s and all registers are cleared. The reset

function is implemented by taking the RESET pin low.

SERIAL INTERFACE

The serial interface is controlled by three pins as follows:

SYNC: This pin is the Frame Synchronization pin for the serial

interface.

SCLK: This pin is the Serial Clock Input. It operates at clock

speeds up to 30 MHz.

DIN: This pin is the Serial Data Input. Data must be valid on

the falling edge of SCLK.

To update a single DAC channel a 19-bit data-word is written

into the AD5532HS. See Table II.

MSB

A4

Table II. Serial Data Format

LSB

A3

A2

A1

A0

DB13–DB0

A4–A0 Bits

Used to address any one of the 32 channels (A4 = MSB of

address, A0 = LSB).

DB13–DB0 Bits

These are used to write a 14-bit word into the addressed

DAC register.

Figure 1 shows the timing diagram for a serial write to the

AD5532HS. The serial interface works with both a continuous and

a noncontinuous serial clock. The first falling edge of SYNC resets

a counter that counts the number of serial clocks to ensure

the correct number of bits are shifted in and out of the serial

shift registers. Any further edges on SYNC are ignored until the

correct number of bits are shifted in or out. Once 19 bits have

been shifted in or out, the SCLK is ignored. In order for another

serial transfer to take place, the counter must be reset by the

falling edge of SYNC. The user must allow 280 ns (min)

between successive writes (refer to Timing Specifications).

–8–

REV. 0

Share Link: