AD8137YR-REEL データシートの表示（PDF） - Analog Devices

部品番号

コンポーネント説明

メーカー

AD8137YR-REEL

Low Cost, Low Power, Differential ADC Driver

Analog Devices 

AD8137

APPLICATIONS

ANALYZING A TYPICAL APPLICATION WITH

MATCHED RF AND RG NETWORKS

Typical Connection and Definition of Terms

Figure 63 shows a typical connection for the AD8137, using

matched external RF/RG networks. The differential input

terminals of the AD8137, VAP and VAN, are used as summing

junctions. An external reference voltage applied to the VOCM

terminal sets the output common-mode voltage. The two

output terminals, VOP and VON, move in opposite directions in a

balanced fashion in response to an input signal.

CF

VIP

RG

VOCM

RG

VIN

RF

VAP

+

VON

AD8137

VAN –

VOP

RF

–

RL, dm VO, dm

+

CF

Figure 63. Typical Connection

The differential output voltage is defined as

VO,dm = VOP − VON

(1)

Common-mode voltage is the average of two voltages. The

output common-mode voltage is defined as

VO, cm =

VOP

+ VON

2

(2)

Output Balance

Output balance is a measure of how well VOP and VON are

matched in amplitude and how precisely they are 180 degrees

out of phase with each other. It is the internal common-mode

feedback loop that forces the signal component of the output

common-mode towards zero, resulting in the near perfectly

balanced differential outputs of identical amplitude and exactly

180 degrees out of phase. The output balance performance does

not require tightly matched external components, nor does it

require that the feedback factors of each loop be equal to each

other. Low frequency output balance is limited ultimately by the

mismatch of an on-chip voltage divider.

Output balance is measured by placing a well matched resistor

divider across the differential voltage outputs and comparing

the signal at the divider’s midpoint with the magnitude of the

differential output. By this definition, output balance is equal to

the magnitude of the change in output common-mode voltage

divided by the magnitude of the change in output differential-

mode voltage:

Output Balance =

∆VO, cm

∆VO, dm

(3)

The differential negative feedback drives the voltages at the sum-

ming junctions VAN and VAP to be essentially equal to each other.

VAN = VAP

(4)

The common-mode feedback loop drives the output common-

mode voltage, sampled at the midpoint of the two internal

common-mode tap resistors in Figure 61, to equal the voltage

set at the VOCM terminal. This ensures that

VOP

= VOCM

+

VO, dm

2

(5)

and

VON

= VOCM

− VO, dm

2

(6)

ESTIMATING NOISE, GAIN, AND BANDWITH WITH

MATCHED FEEDBACK NETWORKS

Estimating Output Noise Voltage and Bandwidth

The total output noise is the root-sum-squared total of several

statistically independent sources. Since the sources are statisti-

cally independent, the contributions of each must be individu-

ally included in the root-sum-square calculation. Table 7 lists

recommended resistor values and estimates of bandwidth and

output differential voltage noise for various closed-loop gains.

For most applications, 1% resistors are sufficient.

Table 7. Recommended Values of Gain-Setting Resistors, and

Voltage Gain for Various Closed-Loop Gains

3 dB

Total Output

Gain RG (Ω) RF (Ω) Bandwidth (MHz) Noise (nV/√Hz)

1

1k

1 k 72

18.6

2

1k

2 k 40

28.9

5

1k

5 k 12

60.1

10 1 k

10 k 6

112.0

The differential output voltage noise contains contributions

from the AD8137’s input voltage noise and input current noise

as well as those from the external feedback networks.

Rev. A | Page 18 of 24

Share Link: