AD9958BCPZ データシートの表示（PDF） - Analog Devices
部品番号
コンポーネント説明
メーカー
AD9958BCPZ Datasheet PDF : 44 Pages
| |||
GENERAL DESCRIPTION
The AD9958 consists of two DDS cores that provide indepen-
dent frequency, phase, and amplitude control on each channel.
This flexibility can be used to correct imbalances between
signals due to analog processing, such as filtering, amplification,
or PCB layout related mismatches. Because both channels share
a common system clock, they are inherently synchronized.
Synchronization of multiple devices is supported.
The AD9958 can perform up to a 16-level modulation of
frequency, phase, or amplitude (FSK, PSK, ASK). Modulation is
performed by applying data to the profile pins. In addition, the
AD9958 also supports linear sweep of frequency, phase, or
amplitude for applications such as radar and instrumentation.
The AD9958 serial I/O port offers multiple configurations to
provide significant flexibility. The serial I/O port offers an SPI-
compatible mode of operation that is virtually identical to the
SPI operation found in earlier Analog Devices, Inc., DDS
products. Flexibility is provided by four data pins (SDIO_0/
SDIO_1/SDIO_2/SDIO_3) that allow four programmable
modes of serial I/O operation.
The AD9958 uses advanced DDS technology that provides low
power dissipation with high performance. The device incorporates
two integrated, high speed 10-bit DACs with excellent wideband
and narrow-band SFDR. Each channel has a dedicated 32-bit
frequency tuning word, 14 bits of phase offset, and a 10-bit
output scale multiplier.
AD9958
The DAC outputs are supply referenced and must be termin-
ated into AVDD by a resistor or an AVDD center-tapped
transformer. Each DAC has its own programmable reference to
enable different full-scale currents for each channel.
The DDS acts as a high resolution frequency divider with the
REFCLK as the input and the DAC providing the output. The
REFCLK input source is common to both channels and can be
driven directly or used in combination with an integrated
REFCLK multiplier (PLL) up to a maximum of 500 MSPS. The
PLL multiplication factor is programmable from 4 to 20, in
integer steps. The REFCLK input also features an oscillator
circuit to support an external crystal as the REFCLK source.
The crystal must be between 20 MHz and 30 MHz. The crystal
can be used in combination with the REFCLK multiplier.
The AD9958 comes in a space-saving 56-lead LFCSP package.
The DDS core (AVDD and DVDD pins) is powered by a 1.8 V
supply. The digital I/O interface (SPI) operates at 3.3 V and
requires the pin labeled DVDD_I/O (Pin 49) be connected
to 3.3 V.
The AD9958 operates over the industrial temperature range of
−40°C to +85°C.
AD9958
32 Σ
32
32 Σ
32
SYNC_IN
SYNC_OUT
I/O_UPDATE
SYNC_CLK
REF_CLK
REF_CLK
ΔFTW
FTW 32
÷4
BUFFER/
XTAL
OSCILLATOR
REF CLOCK
MULTIPLIER
4× TO 20×
CLK_MODE_SEL
DDS CORE
Σ
Σ
COS(X)
15
10
10
DAC
DDS CORE
Σ
Σ
COS(X)
15
10
10
DAC
PHASE/ 14
ΔPHASE
AMP/ 10
ΔAMP
SCALABLE
DAC REF
CURRENT
TIMING AND CONTROL LOGIC
SYSTEM
CLK
CONTROL
REGISTERS
MUX
CHANNEL
REGISTERS
1.8V
1.8V
PROFILE
REGISTERS
AVDD DVDD
P0 P1 P2 P3
Figure 2. Detailed Block Diagram
I/O
PORT
BUFFER
DVDD_I/O
CH0_IOUT
CH0_IOUT
CH1_IOUT
CH1_IOUT
DAC_RSET
PWR_DWN_CTL
MASTER_RESET
SCLK
CS
SDIO_0
SDIO_1
SDIO_2
SDIO_3
Rev. A | Page 3 of 44
Share Link: 