ADN2811(RevA) データシートの表示（PDF） - Analog Devices

部品番号

コンポーネント説明

メーカー

ADN2811
(Rev.:RevA)

OC-48/OC-48 FEC Clock and Data Recovery IC with Integrated Limiting Amp

Analog Devices 

ADN2811

ADN2811

PIN

+

QUANTIZER

0

NIN

50⍀ 50⍀

VREF

1

50⍀ 50⍀

FROM

QUANTIZER

OUTPUT

1

CDR

RETIMED

DATA

CLK

0

VCC

TDINP/N

LOOPEN BYPASS DATAOUTP/N

Figure 16. Test Modes

CLKOUTP/N SQUELCH

APPLICATIONS INFORMATION

PCB Design Guidelines

Proper RF PCB design techniques must be used for optimal performance.

Power Supply Connections and Ground Planes

Use of one low impedance ground plane to both analog and

digital grounds is recommended. The VEE pins should be sol-

dered directly to the ground plane to reduce series inductance.

If the ground plane is an internal plane and connections to the

ground plane are made through vias, multiple vias may be used

in parallel to reduce the series inductance, especially on Pins 33

and 34, which are the ground returns for the output buffers.

Use of a 10 µF electrolytic capacitor between VCC and GND is

recommended at the location where the 3.3 V supply enters the

PCB. Use of 0.1 µF and 1 nF ceramic chip capacitors should be

placed between IC power supply VCC and GND as close as

possible to the ADN2811 VCC pins. Again, if connections to the

supply and ground are made through vias, the use of multiple vias

in parallel will help to reduce series inductance, especially on Pins 35

and 36, which supply power to the high speed CLKOUTP/N and

DATAOUTP/N output buffers. Refer to the schematic in

Figure 17 for recommended connections.

Transmission Lines

Use of 50 Ω transmission lines are required for all high fre-

quency input and output signals to minimize reflections,

including PIN, NIN, CLKOUTP, CLKOUTN, DATAOUTP,

and DATAOUTN (also REFCLKP, REFCLKN for a

155.2 MHz REFCLK). It is also recommended that the

PIN/NIN input traces are matched in length and that the

CLKOUTP/N and DATAOUTP/N output traces are matched

in length. All high speed CML outputs, CLKOUTP/N and

DATAOUTP/N, also require 100 Ω back termination chip

resistors connected between the output pin and VCC. These

resistors should be placed as close as possible to the output

pins. These 100 Ω resistors are in parallel with on-chip 100 Ω

termination resistors to create a 50 Ω back termination (see

Figure 18).

The high speed inputs, PIN and NIN, are internally terminated

with 50 Ω to an internal reference voltage (see Figure 19). A 0.1 µF

capacitor is recommended between VREF, Pin 4, and GND to

provide an ac ground for the inputs.

As with any high speed mixed-signal design, take care to keep

all high speed digital traces away from sensitive analog nodes.

Soldering Guidelines for Chip-Scale Package

The lands on the 48-lead LFCSP are rectangular. The printed

circuit board pad for these should be 0.1 mm longer than the

package land length and 0.05 mm wider than the package land

width. The land should be centered on the pad. This will ensure

that the solder joint size is maximized. The bottom of the chip-

scale package has a central exposed pad. The pad on the printed

circuit board should be at least as large as this exposed pad.

The user must connect the exposed pad to analog VCC.

If vias are used, they should be incorporated into the pad at

1.2 mm pitch grid. The via diameter should be between 0.3 mm

and 0.33 mm and the via barrel should be plated with 1 oz.

copper to plug the via.

–12–

REV. A

Share Link: