APW7334 データシートの表示（PDF） - Anpec Electronics
部品番号
コンポーネント説明
メーカー
APW7334 Datasheet PDF : 15 Pages
| |||
APW7334
Application Information(Cont.)
Output Capacitor Selection (Cont.)
The load transient requirements are the function of the
slew rate (di/dt) and the magnitude of the transient load
urrent. These requirements are generally met with a
mix of capacitors and careful layout. High frequency ca-
pacitors initially supply the transient and slow the current
load rate seen by the bulk capacitors. The bulk filter ca-
pacitor values are generally determined by the ESR
(Effective Series Resistance) and voltage rating require-
ments rather than actual capacitance requirements.
High frequency decoupling capacitors should be placed
as close to the power pins of the load as physically
possible. Be careful not to add inductance in the circuit
board wiring that could cancel the usefulness of these
low inductance components. An aluminum electrolytic
capacitor’s ESR value is related to the case size with lower
ESR available in larger case sizes. However, the Equiva-
lent Series Inductance (ESL) of these capacitors increases
with case size and can reduce the usefulness of the ca-
pacitor to high slew-rate transient loading.
Table1 Capacitor Selection Guide
Vender
Model
Capacitance
(µF)
TC
Voltage
Rating(V)
Si2e
muRata GRM31CR61E106K
10 X5R 25 1206
muRata GRM31CR61C226K
22 X5R 16 1206
VOUT ·(VIN - VOUT) ≤ 1.2
340000 ·L ·VIN
L ≥ VOUT ·(VIN - VOUT)
(H)
408000 ·VIN
where VIN = VIN(MAX)
........... (6)
Table2 Inductor Selection Guide
Vender
Part number
Inductance DCR Current
(µH) (mΩ) Rating(A)
CYNTEC PCMB063T-100MS 10
62
4
Chilisin MHCC10040-100M 10
30
6.5
Gausstek PL94P051M-10U
10
38
3.8
Input Capacitor Selection
A low ESR capacitor is required to keep the noise
minimum. Ceramic capacitors are better, but tantalum or
low ESR electrolytic capacitors may also suffice. When
using tantalum or electrolytic capacitors, a 0.1µF ceramic
capacitor should be placed as close to the IC as possible.
It is recommended that the input EC capacitor should be
added for applications if the APW7334 will suffer high
spike input voltage (ex. hot plug test). It can eliminate the
spike voltage and induced the IC damage from high input
voltage stress.
Inductor Value Calculation
The operating frequency and inductor selection are inter-
related in that higher operating frequencies permit the
use of a smaller inductor for the same amount of inductor
ripple current. However, this is at the expense of efficiency
due to an increase in MOSFET gate charge losses. The
equation (2) shows that the inductance value has a direct
effect on ripple current.
Accepting larger values of ripple current allows the use of
low inductances, but results in higher output voltage ripple
and greater core losses. A reasonable starting point for
setting ripple current is ∆I< 0.4 x IOUT(max). Please be no-
ticed that the maximum ripple current occurs at the maxi-
mum input voltage. The minimum inductance of the in-
uctor is calculated by using the following equation:
CIN1
330µ F/ 25
V/EC x1
VIN
C I N2
22µ F /25 V
/MLCC x1
APW7334
Copyright © ANPEC Electronics Corp.
9
Rev. A.2 - Dec., 2012
www.anpec.com.tw
Share Link: 