AT87F51RC-12AC データシートの表示（PDF） - Atmel Corporation

部品番号

コンポーネント説明

メーカー

AT87F51RC-12AC

8-bit Microcontroller with 32K Bytes QuickFlash™

Atmel Corporation 

AT87F51RC

Special Function Registers

A map of the on-chip memory area called the Special Func-

tion Register (SFR) space is shown in Table 1.

Note that not all of the addresses are occupied, and unoc-

cupied addresses may not be implemented on the chip.

Read accesses to these addresses will in general return

random data, and write accesses will have an indetermi-

nate effect.

User software should not write 1s to these unlisted loca-

tions, since they may be used in future products to invoke

Table 2. T2CON – Timer/Counter 2 Control Register

T2CON Address = 0C8H

Bit Addressable

Bit

TF2

EXF2

RCLK

TCLK

7

6

5

4

new features. In that case, the reset or inactive values of

the new bits will always be 0.

Timer 2 Registers: Control and status bits are contained in

registers T2CON (shown in Table 2) and T2MOD (shown in

Table 4) for Timer 2. The register pair (RCAP2H, RCAP2L)

are the Capture/Reload registers for Timer 2 in 16-bit cap-

ture mode or 16-bit auto-reload mode.

Interrupt Registers: The individual interrupt enable bits

are in the IE register. Two priorities can be set for each of

the six interrupt sources in the IP register.

Reset Value = 0000 0000B

EXEN2

TR2

3

2

C/T2

1

CP/RL2

0

Symbol

TF2

EXF2

RCLK

TCLK

EXEN2

TR2

C/T2

CP/RL2

Function

Timer 2 overflow flag set by a Timer 2 overflow and must be cleared by software. TF2 will not be set when either RCLK = 1

or TCLK = 1.

Timer 2 external flag set when either a capture or reload is caused by a negative transition on T2EX and EXEN2 = 1. When

Timer 2 interrupt is enabled, EXF2 = 1 will cause the CPU to vector to the Timer 2 interrupt routine. EXF2 must be cleared

by software. EXF2 does not cause an interrupt in up/down counter mode (DCEN = 1).

Receive clock enable. When set, causes the serial port to use Timer 2 overflow pulses for its receive clock in serial port

Modes 1 and 3. RCLK = 0 causes Timer 1 overflow to be used for the receive clock.

Transmit clock enable. When set, causes the serial port to use Timer 2 overflow pulses for its transmit clock in serial port

Modes 1 and 3. TCLK = 0 causes Timer 1 overflows to be used for the transmit clock.

Timer 2 external enable. When set, allows a capture or reload to occur as a result of a negative transition on T2EX if Timer

2 is not being used to clock the serial port. EXEN2 = 0 causes Timer 2 to ignore events at T2EX.

Start/Stop control for Timer 2. TR2 = 1 starts the timer.

Timer or counter select for Timer 2. C/T2 = 0 for timer function. C/T2 = 1 for external event counter (falling edge triggered).

Capture/Reload select. CP/RL2 = 1 causes captures to occur on negative transitions at T2EX if EXEN2 = 1. CP/RL2 = 0

causes automatic reloads to occur when Timer 2 overflows or negative transitions occur at T2EX when EXEN2 = 1. When

either RCLK or TCLK = 1, this bit is ignored and the timer is forced to auto-reload on Timer 2 overflow.

5

Share Link: