LC72720YV データシートの表示（PDF） - SANYO -> Panasonic
部品番号
コンポーネント説明
メーカー
LC72720YV Datasheet PDF : 18 Pages
| |||
Sample Application circuit
LC72720YV
10 μF +
Vssa
MPXIN
330 pF
Vdda
0.1 μF
Vssa
560 pF 100 kΩ
1 VREF
2 MPXIN
3 Vdda
5 Vssa
6 FLOUT
7 CIN
9 T1
10 T2
Vssd
NC 11 T3
NC 13 T4
NC 14 T5
15 XOUT
SYR 30 SYR
Vssd
CE 29
CE
DI 28
DI
CL 26
DO 25
RDS-ID 24
SYNC 22
Vddd
10 kΩ
Vddd
10 kΩ
Vddd
10 kΩ
CL
DO
RDS-ID
SYNC
T7 21 NC
T6 20 NC
Vssd 18
Vddd 17
Vssd
0.1 μF
Vddd
XIN 16
16 pF
Vssd
4.332 MHz
16 pF
Vssd
Caution : 1. Determine the value of the DO pin pull-up resistor based on the required serial data transfer speed.
2. A 100-k bias resistor must be connected between the CIN pin and the VREF pin. Note that this resistor
is planned to be included internally to the IC in later versions of this product.
3. If the SYR pin is unused, it must be connected to ground.
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
Regarding monolithic semiconductors, if you should intend to use this IC continuously under high temperature,
high current, high voltage, or drastic temperature change, even if it is used within the range of absolute
maximum ratings or operating conditions, there is a possibility of decrease reliability. Please contact us for a
confirmation.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellectual property rights which has resulted from the use of the technical information and products mentioned
above.
This catalog provides information as of Jun, 2012. Specifications and information herein are subject
to change without notice.
PS No. 6488-18/18
Share Link: 