LT1213MJ8 データシートの表示（PDF） - Linear Technology

部品番号

コンポーネント説明

メーカー

LT1213MJ8

28MHz, 12V/µs, Single Supply Dual and Quad Precision Op Amps

Linear Technology 

LT1213/LT1214

APPLICATI S I FOR ATIO

Supply Voltage

The LT1213/LT1214 op amps are fully functional and all

internal bias circuits are in regulation with 2.2V of supply.

The amplifiers will continue to function with as little as

1.5V, although the input common mode range and the

phase margin are about gone. The minimum operating

supply voltage is guaranteed by the PSRR tests which are

done with the input common mode equal to 500mV and a

minimum supply voltage of 2.5V. The LT1213/LT1214 are

guaranteed over the full – 55°C to 125°C range with a

minimum supply voltage of 2.5V.

The positive supply pin of the LT1213/LT1214 should be

bypassed with a small capacitor (about 0.01µF) within an

inch of the pin. When driving heavy loads and for good

settling time, an additional 4.7µF capacitor should be

used. When using split supplies, the same is true for the

negative supply pin.

Power Dissipation

The LT1213/LT1214 amplifiers combine high speed and

large output current drive into very small packages. Be-

cause these amplifiers work over a very wide supply range,

it is possible to exceed the maximum junction temperature

under certain conditions. To insure that the LT1213/

LT1214 are used properly, calculate the worst case power

dissipation, define the maximum ambient temperature,

select the appropriate package and then calculate the

maximum junction temperature.

The worst case amplifier power dissipation is the total of

the quiescent current times the total power supply voltage

plus the power in the IC due to the load. The quiescent

supply current of the LT1213/LT1214 has a positive tem-

perature coefficient. The maximum supply current of each

amplifier at 125°C is given by the following formula:

ISMAX = 4.2 + 0.048 × (VS – 5) in mA

VS is the total supply voltage.

The power in the IC due to the load is a function of the

output voltage, the supply voltage and load resistance. The

worst case occurs when the output voltage is at half

supply, if it can go that far, or its maximum value if it

cannot reach half supply.

For example, calculate the worst case power dissipation

while operating on ±15V supplies and driving a 500Ω load.

ISMAX = 4.2 + 0.048 × (30 – 5) = 5.4mA

PDMAX = 2 × VS × ISMAX + (VS – VOMAX) × VOMAX/RL

PDMAX = 2 × 15V × 5.4mA + (15V – 7.5V) × 7.5V/500

= 0.162 + 0.113 = 0.275 Watt per Amp

If this is the dual LT1213, the total power in the package is

twice that, or 0.550W. Now calculate how much the die

temperature will rise above the ambient. The total power

dissipation times the thermal resistance of the package

gives the amount of temperature rise. For this example, in

the SO-8 surface mount package, the thermal resistance is

150°C/W junction-to-ambient in still air.

Temperature Rise = PDMAX × θJA = 0.550W × 150°C/W

= 82.5°C

The maximum junction temperature allowed in the plastic

package is 150°C. Therefore the maximum ambient al-

lowed is the maximum junction temperature less the

temperature rise.

Maximum Ambient = 150°C – 82.5°C = 67.5°C

That means the SO-8 dual can be operated at or below

67.5°C on ±15V supplies with a 500Ω load.

As a guideline to help in the selection of the LT1213/

LT1214, the following table describes the maximum sup-

ply voltage that can be used with each part based on the

following assumptions:

1. The maximum ambient is 70°C or 125°C depending on

the part rating.

2. The load is 500Ω including the feedback resistors.

3. The output can be anywhere between the supplies.

PART

LT1213MJ8

LT1213CN8

LT1213CS8

LT1214CN

LT1214CS

MAX SUPPLIES

18.0V or ±14.1V

23.7V or ±18.0V

18.7V or ±14.7V

19.5V or ±15.4V

15.8V or ±12.2V

MAX POWER AT MAX TA

500mW

800mW

533mW

1143mW

800mW

13

Share Link: