LTC2247 データシートの表示（PDF） - Linear Technology
部品番号
コンポーネント説明
メーカー
LTC2247 Datasheet PDF : 24 Pages
| |||
LTC2299
POWER REQUIRE E TS The ● denotes the specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. (Note 8)
SYMBOL
VDD
OVDD
IVDD
PDISS
PSHDN
PNAP
PARAMETER
Analog Supply Voltage
Output Supply Voltage
Supply Current
Power Dissipation
Shutdown Power (Each Channel)
Nap Mode Power (Each Channel)
CONDITIONS
(Note 9)
(Note 9)
Both ADCs at fS(MAX)
Both ADCs at fS(MAX)
SHDN = H, OE = H, No CLK
SHDN = H, OE = L, No CLK
MIN TYP MAX
● 2.7 3 3.4
● 0.5 3 3.6
●
148 172
●
444 516
2
15
UNITS
V
V
mA
mW
mW
mW
WU
TI I G CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. (Note 4)
SYMBOL
fs
tL
PARAMETER
Sampling Frequency
CLK Low Time
tH
CLK High Time
tAP
tD
tMD
Pipeline Latency
Sample-and-Hold Aperture Delay
CLK to DATA Delay
MUX to DATA Delay
Data Access Time After OE↓
BUS Relinquish Time
CONDITIONS
(Note 9)
Duty Cycle Stabilizer Off
Duty Cycle Stabilizer On (Note 9)
Duty Cycle Stabilizer Off
Duty Cycle Stabilizer On (Note 9)
CL = 5pF (Note 7)
CL = 5pF (Note 7)
CL = 5pF (Note 7)
(Note 7)
MIN TYP MAX
●1
80
● 5.9 6.25 500
● 5 6.25 500
● 5.9 6.25 500
● 5 6.25 500
0
● 1.4 2.7 5.4
● 1.4 2.7 5.4
●
4.3 10
●
3.3 8.5
5
UNITS
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
Cycles
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: All voltage values are with respect to ground with GND and OGND
wired together (unless otherwise noted).
Note 3: When these pin voltages are taken below GND or above VDD, they
will be clamped by internal diodes. This product can handle input currents
of greater than 100mA below GND or above VDD without latchup.
Note 4: VDD = 3V, fSAMPLE = 80MHz, input range = 2VP-P with differential
drive, unless otherwise noted.
Note 5: Integral nonlinearity is defined as the deviation of a code from a
straight line passing through the actual endpoints of the transfer curve.
The deviation is measured from the center of the quantization band.
Note 6: Offset error is the offset voltage measured from –0.5 LSB when
the output code flickers between 00 0000 0000 0000 and
11 1111 1111 1111.
Note 7: Guaranteed by design, not subject to test.
Note 8: VDD = 3V, fSAMPLE = 80MHz, input range = 1VP-P with differential
drive. The supply current and power dissipation are the sum total for both
channels with both channels active.
Note 9: Recommended operating conditions.
2299fa
5
Share Link: 