MACH111-10VC データシートの表示（PDF） - Advanced Micro Devices

部品番号

コンポーネント説明

メーカー

MACH111-10VC

High-Performance EE CMOS Programmable Logic

Advanced Micro Devices 

ABSOLUTE MAXIMUM RATINGS

Storage Temperature . . . . . . . . . . . . . –65°C to +150°C

Ambient Temperature

with Power Applied . . . . . . . . . . . . . –55°C to +125°C

Device Junction Temperature . . . . . . . . . . . . . +150°C

Supply Voltage

with Respect to Ground . . . . . . . . . . –0.5 V to +7.0 V

DC Input Voltage . . . . . . . . . . . .–0.5 V to VCC + 0.5 V

DC Output

or I/O Pin Voltage. . . . . . . . . . . –0.5 V to VCC + 0.5 V

Static Discharge Voltage . . . . . . . . . . . . . . . . . 2001 V

Latchup Current (TA = –40°C to +85°C) . . . . . . 200 mA

Stresses above those listed under Absolute Maximum

Ratings may cause permanent device failure. Functionality at or

above these limits is not implied. Exposure to Absolute Maximum

Ratings for extended periods may affect device reliability.

OPERATING RANGES

Industrial (I) Devices

Temperature (TA)

Operating in Free Air . . . . . . . . . . . . . . –40°C to +85°C

Supply Voltage (VCC)

with Respect to Ground . . . . . . . . . . . +4.5 V to +5.5 V

Operating ranges define those limits between which the

functionality of the device is guaranteed.

DC CHARACTERISTICS over INDUSTRIAL operating ranges

Parameter

Symbol Parameter Description

Test Conditions

Min Typ Max Unit

VOH Output HIGH Voltage

IOH = –3.2 mA, VCC = Min, VIN = VIH or VIL

2.4

VOL

Output LOW Voltage

IOL = 16 mA, VCC = Min, VIN = VIH or VIL

VIH

Input HIGH Voltage

Guaranteed Input Logical HIGH Voltage for all

Inputs (Note 1)

2.0

V

0.5

V

V

VIL

IIH

IIL

IOZH

IOZL

ISC

ICC

Input LOW Voltage

Input HIGH Current

Input LOW Current

Off-State Output Leakage

Current HIGH

Off-State Output Leakage

Current LOW

Output Short-Circuit

Current

Supply Current (Static)

Supply Current (Active)

Guaranteed Input Logical LOW Voltage for all

Inputs (Note 1)

VIN = 5.25 V, VCC = Max (Note 2)

VIN = 0 V, VCC = Max (Note 2)

VOUT = 5.25 V, VCC = Max

VIN = VIH or VIL (Note 2)

VOUT = 0 V, VCC = Max

VIN = VIH or VIL (Note 2)

VOUT = 0.5 V, VCC = Max (Note 3)

VCC = 5 V, TA = 25°C, f = 0 MHz (Note 4)

VCC = 5 V, TA = 25°C, f = 1 MHz (Note 4)

0.8

V

10

µA

–10

µA

10

µA

–10

µA

–30

–160 mA

40

mA

45

mA

Notes:

1. These are absolute values with respect to device ground and all overshoots due to system and/or tester noise are included.

2. I/O pin leakage is the worst case of IIL and IOZL (or IIH and IOZH).

3. Not more than one output should be shorted at a time. Duration of the short-circuit should not exceed one second.

VOUT = 0.5 V has been chosen to avoid test problems caused by tester ground degradation.

4. Measured with a 16-bit up/down counter program in low-power mode. This pattern is programmed in each PAL block and is

capable of being enabled and reset.

MACH111-7/10/12/14/18 (Ind)

13

Share Link: