MACH220-10 データシートの表示（PDF） - Advanced Micro Devices
部品番号
コンポーネント説明
メーカー
MACH220-10 Datasheet PDF : 33 Pages
| |||
AMD
ABSOLUTE MAXIMUM RATINGS
Storage Temperature . . . . . . . . . . . . 65°C to +150°C
Ambient Temperature
with Power Applied . . . . . . . . . . . . . –55°C to +125°C
Supply Voltage with
Respect to Ground . . . . . . . . . . . . . –0.5 V to +7.0 V
DC Input Voltage . . . . . . . . . . . . –0.5 V to VCC+ 0.5 V
DC Output or
I/O Pin Voltage . . . . . . . . . . . . . –0.5 V to VCC+ 0.5 V
Static Discharge Voltage . . . . . . . . . . . . . . . . . 2001 V
Latchup Current
(TA = –40°C to +85°C) . . . . . . . . . . . . . . . . . . 200 mA
Stresses above those listed under Absolute Maximum Ratings
may cause permanent device failure. Functionality at or above
these limits is not implied. Exposure to Absolute Maximum
Ratings for extended periods may affect device reliability.
Programming conditions may differ.
INDUSTRIAL OPERATING RANGES
Ambient Temperature (TA)
Operating in Free Air . . . . . . . . . . . . –40°C to +85°C
Supply Voltage (VCC) with
Respect to Ground . . . . . . . . . . . . . . +4.5 V to +5.5 V
Operating ranges define those limits between which the func-
tionality of the device is guaranteed.
DC CHARACTERISTICS over INDUSTRIAL operating ranges unless otherwise specified
Parameter
Symbol
Parameter Description
Test Conditions
Min Typ Max Unit
VOH
Output HIGH Voltage
VOL
Output LOW Voltage
VIH
Input HIGH Voltage
IOH = –3.2 mA, VCC = Min
VIN = VIH or VIL
IOL = 16 mA, VCC = Min
VIN = VIH or VIL
Guaranteed Input Logical HIGH
Voltage for all Inputs (Note 1)
2.4
V
0.5 V
2.0
V
VIL
Input LOW Voltage
Guaranteed Input Logical LOW
Voltage for all Inputs (Note 1)
0.8 V
IIH
Input HIGH Leakage Current
VIN = 5.25 V, VCC = Max (Note 2)
10 µA
IIL
Input LOW Leakage Current
VIN = 0 V, VCC = Max (Note 2)
–100 µA
IOZH
Off-State Output Leakage
Current HIGH
VOUT = 5.25 V, VCC = Max
VIN = VIH or VIL (Note 2)
10 µA
IOZL
Off-State Output Leakage
Current LOW
VOUT = 0 V, VCC = Max
VIN = VIH or VIL (Note 2)
–100 µA
ISC
Output Short-Circuit Current
VOUT = 0.5 V, VCC = Max (Note 3)
–30
–130 mA
ICC
Supply Current (Typical)
VCC = 5 V, TA = 25°C, f = 25 MHz (Note 4)
205
mA
Notes:
1. These are absolute values with respect to device ground and all overshoots due to system and/or tester noise are included.
2. I/O pin leakage is the worst case of IIL and IOZL(or IIH and IOZH).
3. Not more than one output should be shorted at a time. Duration of the short-circuit should not exceed one second.
VOUT = 0.5 V has been chosen to avoid test problems caused by tester ground degradation.
4. Measured with a 12-bit up/down counter pattern. This pattern is programmed in each PAL block and is capable of
being loaded, enabled, and reset.
14
MACH220-14/18/24 (Ind)
Share Link: 