PIC10F200(2014) データシートの表示（PDF） - Microchip Technology

部品番号

コンポーネント説明

メーカー

PIC10F200
(Rev.:2014)

6-Pin, 8-Bit Flash Microcontrollers

Microchip Technology 

PIC10F200/202/204/206

TABLE 5-2: SUMMARY OF PORT REGISTERS

Address Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2 Bit 1 Bit 0

Value on

Power-On

Reset

Value on

All Other Resets

N/A

TRISGPIO —

—

—

— I/O Control Register

---- 1111 ---- 1111

N/A

OPTION GPWU GPPU T0CS T0SE PSA PS2 PS1 PS0 1111 1111 1111 1111

03h

STATUS GPWUF CWUF —

TO

PD

Z

DC

C 00-1 1xxx qq-q quuu(1), (2)

06h

GPIO

—

—

—

— GP3 GP2 GP1 GP0 ---- xxxx ---- uuuu

Legend:

Note 1:

2:

Shaded cells are not used by PORT registers, read as ‘0’, – = unimplemented, read as ‘0’, x = unknown, u = unchanged,

q = depends on condition.

If Reset was due to wake-up on pin change, then bit 7 = 1. All other Resets will cause bit 7 = 0.

If Reset was due to wake-up on comparator change, then bit 6 = 1. All other Resets will cause bit 6 = 0.

5.4 I/O Programming Considerations

5.4.1 BIDIRECTIONAL I/O PORTS

Some instructions operate internally as read followed

by write operations. The BCF and BSF instructions, for

example, read the entire port into the CPU, execute the

bit operation and rewrite the result. Caution must be

used when these instructions are applied to a port

where one or more pins are used as input/outputs. For

example, a BSF operation on bit 2 of GPIO will cause

all eight bits of GPIO to be read into the CPU, bit 2 to

be set and the GPIO value to be written to the output

latches. If another bit of GPIO is used as a bidirectional

I/O pin (say bit 0), and it is defined as an input at this

time, the input signal present on the pin itself would be

read into the CPU and rewritten to the data latch of this

particular pin, overwriting the previous content. As long

as the pin stays in the Input mode, no problem occurs.

However, if bit 0 is switched into Output mode later on,

the content of the data latch may now be unknown.

Example 5-1 shows the effect of two sequential

Read-Modify-Write instructions (e.g., BCF, BSF, etc.)

on an I/O port.

A pin actively outputting a high or a low should not be

driven from external devices at the same time in order

to change the level on this pin (“wired OR”, “wired

AND”). The resulting high output currents may damage

the chip.

EXAMPLE 5-1:

READ-MODIFY-WRITE

INSTRUCTIONS ON AN

I/O PORT

;Initial GPIO Settings

;GPIO<3:2> Inputs

;GPIO<1:0> Outputs

;

;

;

BCF

BCF

MOVLW

TRIS

;

GPIO,

GPIO,

007h;

GPIO

GPIO latch

----------

1 ;---- pp01

0 ;---- pp10

;---- pp10

GPIO pins

----------

---- pp11

---- pp11

---- pp11

Note 1:

The user may have expected the pin values to

be ---- pp00. The 2nd BCF caused GP1 to

be latched as the pin value (High).

5.4.2

SUCCESSIVE OPERATIONS ON

I/O PORTS

The actual write to an I/O port happens at the end of an

instruction cycle, whereas for reading, the data must be

valid at the beginning of the instruction cycle (Figure 5-2).

Therefore, care must be exercised if a write followed by

a read operation is carried out on the same I/O port. The

sequence of instructions should allow the pin voltage to

stabilize (load dependent) before the next instruction

causes that file to be read into the CPU. Otherwise, the

previous state of that pin may be read into the CPU rather

than the new state. When in doubt, it is better to separate

these instructions with a NOP or another instruction not

accessing this I/O port.

 2004-2014 Microchip Technology Inc.

DS40001239F-page 21

Share Link: