DatasheetQ Logo
Electronic component search and free download site. Transistors,MosFET ,Diode,Integrated circuits

SP8510KN データシートの表示(PDF) - Signal Processing Technologies

部品番号
コンポーネント説明
メーカー
SP8510KN
Sipex
Signal Processing Technologies Sipex
SP8510KN Datasheet PDF : 12 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
PINOUT
N.C. 1
±10V IN 2
±5V IN 3
VREF 4
AGND 5
D11 6
D10 7
D9 8
D8 9
D7 10
D6 11
D5 12
D4 13
N.C. 14
SP8503
SP8505
SP8510
28 N.C.
27 VSA
26 VSD
25 N.C.
24 BUSY
23 CS
22 R/C
21 HBE
20 D0
19 D1
18 D2
17 D3
16 DGND
15 N.C.
PIN ASSIGNMENT
Pin 1 —No Connection —This pin is not internally
connected.
Pin 2 — IN
1
±10V Analog Input. Connected to
AGND for ±5V range.
Pin 3 — IN2 ±5V Analog Input. Connected to
AGND for ±10V range.
Pin 4 — VREF – Internal Voltage. Reference Output.
Pin 5 — AGND — Analog Ground. Connect
to pin 16 at the device.
Pin 6 — D11 — Data Bit 11. Most Significant Bit
(MSB).
Pin 7 — D10 — Data Bit 10.
Pin 8— D — Data Bit 9.
9
Pin 9 — D8 — Data Bit 8.
Pin 10 — D7 — Data Bit 7 if HBE is LOW; LOW if
HBE is HIGH.
Pin 11 — D6 — Data Bit 6 if HBE is LOW; LOW if
HBE is HIGH.
Pin 12 — D5 — Data Bit 5 if HBE is LOW; LOW if
HBE is HIGH.
Pin 13 — D4 — Data Bit 4 if HBE is LOW; LOW if
HBE is HIGH.
Pin 14 —N.C.—This pin is not internally connected.
Pin 15 —N.C.—This pin is not internally connected.
Pin 16— DGND — Digital Ground. Connect
to pin 5, at the device.
Pin 17 — D3 — Data Bit 3 if HBE is LOW; Data Bit
11 if HBE is HIGH.
Pin 18 — D2 — Data Bit 2 if HBE is LOW; Data Bit
10 if HBE is HIGH.
Pin 19— D1 — Data Bit 1 if HBE is LOW; Data Bit
9 if HBE is HIGH.
Pin 20 — D0 — Data Bit 0 if HBE is LOW. Least
Significant Bit (LSB). Data Bit 8 if HBE is HIGH.
Pin 21 — HBE — High Byte Enable, When held
LOW, data output as 12-bits in parallel. When held
HIGH, four MSBs presented on pins 17–20, pins
10 – 13 output LOWs. Must be LOW to initiate
conversion.
Pin 22— R/C — Read/Convert. Falling edge initiates
conversion when CS is LOW, HBE is LOW, and
BUSY is HIGH.
Pin 23 — CS — Chip Select. Outputs in Hi-Z state
when HIGH. Must be LOW to initiate conversion or
read data.
Pin 24 — BUSY. Output LOW during conver-
sion. Data valid on rising edge in Convert
Mode.
Pin 25 — N.C. — This pin is not internally connected.
Pin 26 — VSD — Positive Digital Power Supply, +5V.
Connect to pin 27, and bypass to DGND.
Pin 27 — VSA — Positive Analog Power Supply.
+5V. Connect to pin 26, and bypass to AGND.
Pin 28 — N.C. — This pin is not internally connected.
46

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]