ACPL-M43T データシートの表示（PDF） - Avago Technologies

部品番号

コンポーネント説明

メーカー

ACPL-M43T

Automotive Wide Operating Temperature 1MBd Digital Optocoupler in a 5-Pin Surface Mount Plastic Package

Avago Technologies 

Switching Specifications (AC)

Over recommended operating (TA = -40°C to 125°C), IF = 10mA, VCC = 5.0 V unless otherwise specified.

Parameter

Symbol Min Typ Max Units

Test Conditions

Fig. Note

Propagation Delay

TPHL

Time to Logic Low

at Output

0.08 0.2 0.8 µs

0.06

1.0 µs

TA=25°C Pulse: f=10kHz, Duty cycle =50%, 5,6, 9

IF = 10mA, VCC = 5.0 V, RL = 1.9kW, 8

CL = 15pF VTHHL=1.5V

Propagation Delay

TPLH

Time to Logic High

at Output

0.15 0.3 0.8 µs

0.03

1.0 µs

TA=25°C Pulse: f=10kHz, Duty cycle =50%, 5,6, 9

IF = 10mA, VCC = 5.0 V, RL = 1.9kW 8

CL = 15pF VTHLH=2.0V

Pulse Width

Distortion

PWD

0

0.4 0. 45 µs

TA=25°C Pulse: f=10kHz, Duty cycle =50%,

12

0

0.85 µs

IF=10mA, VCC=5.0V, RL=1.9kW,

CL=15pF, VTHHL=1.5V, VTHLH=2.0V

Propagation Delay

tPLH-tPHL 0

0.4 0.5 µs

TA=25°C Pulse: f=10kHz, Duty cycle =50%,

13

Difference Between

Any 2 Parts

0

0.9 µs

IF=10mA, VCC=5.0V, RL=1.9kW,

CL=15pF, VTHHL=1.5V, VTHLH=2.0V

Common Mode

Transient Immunity

at Logic High Output

|CMH|

15 30

kV/μs

VCM=1500Vp-p, IF=0mA, TA=25°C, 9 8, 9

RL=1.9kW

Common Mode

Transient Immunity

at Logic Low Output

|CML|

15 30

kV/μs

VCM=1500Vp-p, IF=10mA,

TA=25°C, RL=1.9kW

Package Characteristics

*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an in-

put-output continuous voltage rating.

Parameter

Input-Output Momentary

Withstand Voltage*

Input-Output Resistance

Symbol Min. Typ. Max. Units Test Conditions

Fig. Note

VISO

3750

Vrms RH ≤ 50%, t = 1 min;

6, 7

TA = 25°C

RI-O

1012

W

VI-O = 500 Vdc

6

Input-Output Capacitance

CI-O

0.6

pF

f = 1 MHz; VI-O = 0 Vdc

6

Notes:

1. Derate linearly above 85°C free-air temperature at a rate of 0.25 mA/°C.

2. Derate linearly above 85°C free-air temperature at a rate of 0.30 mA/°C.

3. Derate linearly above 85°C free-air temperature at a rate of 0.375 mW/°C.

4. Derate linearly above 85°C free-air temperature at a rate of 1.875 mW/°C.

5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times 100.

6. Device considered a two terminal device: pins 1 and 3 shorted together, and pins 4, 5 and 6 shorted together.

7. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 VRMS for 1 second (leakage detection

current limit, II-O ≤ 5 µA).

8. Common transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the rising edge of the common mode pulse, VCM,

to assure that the output will remain in a Logic High state (i.e., VO > 2.0 V). Common mode transient immunity in a Logic Low level is the maximum

tolerable (negative) dVCM/dt on the falling edge of the common mode pulse signal, VCM to assure that the output will remain in a Logic Low state

(i.e., VO < 0.8 V).

9. The 1.9 kΩ load represents 1 TTL unit load of 1.6 mA and the 5.6 kΩ pull-up resistor.

10. The frequency at which the ac output voltage is 3 dB below its mid-frequency value.

11. Use of a 0.1 µF bypass capacitor connected between pins 4 and 6 is recommended.

12. Pulse Width Distortion (PWD) is defined as |tPHL - tPLH| for any given device.

13. The difference between tPLH and tPHL between any two parts under the same test condition.



Share Link: