M65580MAP データシートの表示（PDF） - Mitsumi

部品番号

コンポーネント説明

メーカー

M65580MAP

Digital Video/Chroma/Deflection+MCU

Mitsumi 

Preliminary

Note : This is not a final specification.

Some of information in this document are subject to changes.

Mitsubishi Semiconductor<Digital IC>

M65580MAP-XXXFP

Digital Video/Chroma/Deflection+MCU

Electrical characteristics (MCU part)

Symbol

ICC

VOH

VOL

VT+ – VT–

IIZH

IIZL

RBS

Parameter

(Vcc=5V±10%, Vss = 0V, f(XIN)=8MHz, Ta=–20˚C to 65˚C, unless otherwise noted)

Test conditions

Limits

Unit Test

Min. Typ. Max.

circuit

VCC = 5.5 V,

f(XIN) = 8 MHz

OSD OFF

Data slicer OFF

OSD ON

15 30

mA

30 45

Power source current

System operation VCC = 5.5 V, f(XIN) = 0,

f(XCIN) = 32 kHz,

OSD OFF, Data slicer OFF,

Low-power dissipation mode set

(CM5 = "0", CM6 = "1")

60 200 µA

1

Wait mode VCC = 5.5 V, f(XIN) = 8 MHz

2

4 mA

VCC = 5.5 V, f(XIN) = 0,

f(XCIN) = 32 kHz,

Low-power dissipation mode set

(CM5 = "0", CM6 = "1")

25 100 µA

VCC = 5.5 V, f(XIN) = 0,

f(XCIN) = 0

1

10

HIGH output voltage P10–P16, P20–P27,

P30, P31, P52, P53

VCC = 4.5 V

IOH = –0.5 mA

2.4

V

2

LOW output voltage

P00–P07, P10,

P15, P16, P20–P27,

P30, P31, P52, P53

VCC = 4.5 V

IOL = 0.5 mA

0.4 V

LOW output voltage P11–P14

VCC = 4.5 V

IOL = 3 mA

0.4

IOL = 6 mA

0.6

Hysteresis (See note 1)

RESET, P50–P51, INT1, INT2,

INT3, TIM2, TIM3, SIN, SCLK, SCL1,

SCL2, SDA1, SDA2

VCC = 5.0 V

0.5 1.3 V 3

HIGH input leak current

P00–P07, P10–P16, P20–P27,

P50, P51, RESET

VCC = 5.5 V

VI = 5.5 V

5 µA 4

LOW input leak current

P00–P07, P10–P16, P20–P27,

P50, P51, RESET

I2C-BUS • BUS switch connection resistor

(between SCL1 and SCL2, SDA1 and SDA2)

VCC = 5.5 V

VI = 0 V

VCC = 4.5 V

5 µA 4

130

5

Notes 1: P06, P07, P15, P23, P24 have the hysteresis when these pins are used as interrupt input pins or timer input pins. P11–P14 have the hysteresis when these

pins are used as multi-master I2C-BUS interface ports. P20–P22 have the hysteresis when these pins are used as serial I/O pins.

2: Connect 0.1µF or more capacitor externally between the power source pins VCC–VSS so as to reduce power source noise.

Also connect 0.1µF or more capacitor externally between the pins VCC–CNVSS.

3: Use a quartz-crystal oscillator or a ceramic resonator for the CPU oscillation circuit. When using the data slicer, use 8 MHz.

4: Pin names in each parameter is described as bellow.

(1) Dedicated pin: dedicated pin names.

(2) Double-/triple-function ports

• When the same limits: I/O port name.

• When the limits of functions except ports are different from I/O port limits: function pin name.

MITSUBISHI

14

Share Link: