MF007M5-03ATXX データシートの表示（PDF） - Mitsumi

部品番号

コンポーネント説明

メーカー

MF007M5-03ATXX

8/16-bit Data Bus Flash ATA PC Card

Mitsumi 

MITSUBISHI STORAGE CARD

Check Power Mode(98h, E5h)

This command checks the power mode.

Execute Drive Diagnostic(90h)

This command performs the internal diagnostic tests

implemented by the card.

Erase Sector(s)(C0h)

This command is used to pre-erase and condition data

sectors in advance of a Write without Erase or Write

Multiple without Erase command.

Format Track(50h)

This command writes the desired head and cylinder of the

selected drive with a FFh pattern.

Identify Drive(ECh)

This command enables the host to receive parameter

information from the card. (Refer to the Identify Drive

Information table.)

Idle(97h, E3h)

This command causes the card to set BSY, enter the Idle

mode, clear BSY and generate an interrupt. If the sector

count is non-zero, the automatic power down mode is

enabled. If the sector count is zero, the automatic power

down mode is disabled.

Idle Immediate(95h, E1h)

This command causes the card to set BSY, enter the idle

mode, clear BSY and generate an interrupt.

Initialize Drive Parameters(91h)

This command allows the host to alter the number of

sectors per track and the number of heads per cylinder.

Read Buffer(E4h)

This command enables the host to read the current

contents of the card’s sector buffer.

Read Long Sector(22h, 23h)

This command is similar to the Read Sector(s) command

except the contents of the Sector Count register are

ignored and only one sector is read. The 512 data bytes

and 4 ECC bytes are read into the buffer(with no ECC

correction) and then transferred to the host.

Read Multiple(C4h)

This command performs similarly to the Read Sector(s)

command. Interrupt are not generated on each sector, but

on the transfer of a block which contains the number of

sectors defined by a Set Multiple command.

Read Sector(s)(20h, 21h)

This command transfers data from the card to the host.

Data transfer starts at the sector specified by the Cylinder,

Head, and Sector Number registers, and proceeds for the

number of sectors specified in the Sector Count register.

ATA PC CARDS

Read Verify Sector(s)(40h, 41h)

This command is identical to the Read Sector(s)

command, except that DRQ is not asserted, and no data is

transferred to the host.

Recalibrate(1xh)

Although this command is supported for backward

compatibility, it has no actual function. The card will

always return good status at the completion of this

command.

Request Sense(03h)

This command requests extended error information for the

previous command.

Seek(7xh)

This command is supported for backward compatibility.

Although this command has no actual function, it does

perform a range check of valid track, and posts an IDNF

error if the Head or Cylinder specified are out of bounds.

Set Features(EFh)

This command is used by the host to establish or select

certain features.

Set Multiple Mode(C6h)

This command enables the card to perform Read and

Write Multiple operations and establishes the block count

for these commands. This card supports 1 sector block

size.

Set Sleep Mode(E6h, 99h)

This command causes the card to set BSY, enter the Sleep

mode, clear BSY and generate an interrupt.

Standby(96h, E2h)

This command causes the card to set BSY, enter the

Standby mode, clear BSY and generate an interrupt.

Standby Immediate(94h, E0h)

This command causes the card to set BSY, enter the

Standby mode, clear BSY and generate an interrupt.

Wear Leveling(F5h)

Although this command is supported for backward

compatibility, it has no actual function. The card will

always return good status at the completion of this

command.

Write Buffer(E8h)

This command enables the host to overwrite contents of

the card’s sector buffer with any data pattern desired. This

command has the same protocol as the Write Sector(s)

command and transfers 512 bytes.

Write Long Sector(32h, 33h)

This command is similar to the Write Sector(s) except the

contents of the Sector Count register are ignored and only

MITSUBISHI

ELECTRIC

18

1997.Nov. Rev. 1.2

Share Link: