MSK4223D データシートの表示（PDF） - M.S. Kennedy Corporation
部品番号
コンポーネント説明
メーカー
MSK4223D Datasheet PDF : 6 Pages
| |||
ABSOLUTE MAXIMUM RATINGS 3
V+
VCC
IOUT
IPK
VOUT
θJC
High Voltage Supply 75V 4
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Logic Supply 16V ○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Continuous Output Current ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 6A
Peak Output Current 9A ○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Output Voltage Range ○ ○GND-2V min. To V+ max.
Thermal Resistance ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 4.6°C/W
(Output Switches)
TST Storage Temperature Range ○ 5 ○-65°C to +150°C
TLD Lead Temperature Range
(10 Seconds Lead Only) ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 200°C
TC Case Operating Temperature
MSK4223 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ -40°C to +125°C
TJ
Junction Temperature
+150°C
○
○
○
○
○
○
○
○
○
○
○
ELECTRICAL SPECIFICATIONS
All Ratings: Tc= +25°C Unless Otherwise Specified
Parameter
Test Conditions 2
Min.
MSK4223
Typ.
Max.
Units
OUTPUT CHARACTERISTICS
VDS(ON) Voltage 1
Instantaneous Forward Voltage 1
Reverse Recovery Time 1
Leakage Current 1
PWM Frequency
VCC SUPPLY CHARACTERISTICS
Quiescent Bias Current
VCC Voltage Range 1
INPUT SIGNAL CHARACTERISTICS
Analog Input Voltage
Analog Input Voltage
Analog Input Voltage
LOGIC CONTROL INPUTS 1
Disable Input
HEN Input
SWITCHING CHARACTERISTICS 1
Rise-Time
Fall-Time
Dead-Time
Each MOSFET ID=6A
Each MOSFET IS=6A Intrinsic Diode
Intrinsic Diode
Each MOSFET V+=70V
Analog Input=6VDC RL=∞
Output A,B=50% Duty Cycle
Output A=100% Duty Cycle High
Output B=100% Duty Cycle High
Input Voltage LO
Input Voltage HI
Input Current (DISABLE=0V)
Input Voltage LO
Input Voltage HI
Input Current (HEN=0V)
RL=100Ω
V+=75V
V+=75V
-
0.75
1.5
V
-
1.1
1.8
V
-
-
260
nS
-
1.0
25
uA
225
250
275
KHz
-
46
60
mA
9
12
16
V
5.5
6
6.5
V
2.5
3
3.5
V
8.5
9
9.5
V
-
-
0.8
V
2.7
-
-
V
-
-
-135
uA
-
-
0.8
V
2.7
-
-
V
-
-
-270
uA
-
56
84
nS
-
33
50
nS
-
100
-
nS
NOTES:
1 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only.
2 VCC=+12V, V+=28V, RL=1K AOUT to BOUT, unless otherwise specified.
3 Continuous operation at or above absolute maximum ratings may adversely effect the device performance and/or life cycle.
4 When applying power to the device, apply the low voltage followed by the high voltage or alternatively, apply both at the
same time. Do not apply high voltage without low voltage present.
5 Internal solder reflow temperature is 180°C, do not exceed.
2
8548-140 Rev. J 10/14
Share Link: 