DSPIC33FJ06GS101 データシートの表示（PDF） - Microchip Technology

部品番号

コンポーネント説明

メーカー

DSPIC33FJ06GS101

High-Performance, 16-bit Digital Signal Controllers

Microchip Technology 

dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04

2.0 GUIDELINES FOR GETTING

STARTED WITH 16-BIT

DIGITAL SIGNAL

CONTROLLERS

Note:

This data sheet summarizes the features

of the dsPIC33FJ06GS101/X02 and

dsPIC33FJ16GSX02/X04 family of

devices. It is not intended to be a

comprehensive reference source. To

complement the information in this data

sheet, refer to the dsPIC33F Family

Reference Manual, which is available from

the

Microchip

website

(www.microchip.com).

2.1 Basic Connection Requirements

Getting started with the dsPIC33FJ06GS101/X02 and

dsPIC33FJ16GSX02/X04 family of 16-bit Digital Signal

Controllers (DSC) requires attention to a minimal set of

device pin connections before proceeding with

development. The following is a list of pin names, which

must always be connected:

• All VDD and VSS pins

(see Section 2.2 “Decoupling Capacitors”)

• All AVDD and AVSS pins (regardless if ADC module

is not used)

(see Section 2.2 “Decoupling Capacitors”)

• VCAP/VDDCORE

(see Section 2.3 “Capacitor on Internal Voltage

Regulator (VCAP/VDDCORE)”)

• MCLR pin

(see Section 2.4 “Master Clear (MCLR) Pin”)

• PGECx/PGEDx pins used for In-Circuit Serial

Programming™ (ICSP™) and debugging purposes

(see Section 2.5 “ICSP Pins”)

• OSC1 and OSC2 pins when external oscillator

source is used

(see Section 2.6 “External Oscillator Pins”)

2.2 Decoupling Capacitors

The use of decoupling capacitors on every pair of

power supply pins, such as VDD, VSS, AVDD and

AVSS is required.

Consider the following criteria when using decoupling

capacitors:

• Value and type of capacitor: Recommendation

of 0.1 μF (100 nF), 10-20V. This capacitor should

be a low-ESR and have resonance frequency in

the range of 20 MHz and higher. It is

recommended that ceramic capacitors be used.

• Placement on the printed circuit board: The

decoupling capacitors should be placed as close

to the pins as possible. It is recommended to

place the capacitors on the same side of the

board as the device. If space is constricted, the

capacitor can be placed on another layer on the

PCB using a via; however, ensure that the trace

length from the pin to the capacitor is within

one-quarter inch (6 mm) in length.

• Handling high frequency noise: If the board is

experiencing high frequency noise, upward of

tens of MHz, add a second ceramic-type capacitor

in parallel to the above described decoupling

capacitor. The value of the second capacitor can

be in the range of 0.01 μF to 0.001 μF. Place this

second capacitor next to the primary decoupling

capacitor. In high-speed circuit designs, consider

implementing a decade pair of capacitances as

close to the power and ground pins as possible.

For example, 0.1 μF in parallel with 0.001 μF.

• Maximizing performance: On the board layout

from the power supply circuit, run the power and

return traces to the decoupling capacitors first,

and then to the device pins. This ensures that the

decoupling capacitors are first in the power chain.

Equally important is to keep the trace length

between the capacitor and the power pins to a

minimum thereby reducing PCB track inductance.

© 2009 Microchip Technology Inc.

Preliminary

DS70318D-page 19

Share Link: