TDA8263HN データシートの表示（PDF） - Philips Electronics
部品番号
コンポーネント説明
メーカー
TDA8263HN Datasheet PDF : 28 Pages
| |||
Philips Semiconductors
TDA8263HN
Fully integrated satellite tuner
Table 39: Characteristics …continued
Tamb = 25 °C; VCC = 3.3 V; output level on differential I/Q output is 550 mV (p-p); unless otherwise specified.
Symbol Parameter
Conditions
Min Typ Max Unit
ΦNosc
oscillator phase noise in the
satellite band
100 kHz offset, out of the PLL
[4] -
−100 −94 dBc/Hz
bandwidth
SNFSB
MDR
synthesizer noise floor in the
satellite band
main divider ratio
1 kHz and 10 kHz offset;
fcomp = 1 MHz
[4] -
-
128 -
−78 dBc/Hz
32 767
Crystal oscillator and XTOUT
Zosc
crystal oscillator negative
impedance
absolute value
500 -
-
Ω
fXTAL
ZXTAL
crystal frequency
recommended crystal series
resistance
16 16 16
MHz
-
-
150 Ω
Vo(p-p)
MS input
output voltage (peak-to-peak value) crystal output
550 750 -
mV
Ih
HIGH level input current
Il
LOW level input current
Charge pump and tuning voltage
VMS = VCC
VMS = 0 V
−50 -
−50 -
+50 µA
+50 µA
Il
Il(min)
Il(max)
charge pump leakage current
charge pump low, minimum current CPHIGH = 0 and CPCURSEL = 0
charge pump low, maximum
current
CPHIGH = 0 and CPCURSEL = 1
−10 0
+10 nA
0.67 0.9 1.13 mA
0.97 1.3 1.63 mA
Ih(min)
charge pump high, minimum
current
CPHIGH = 1 and CPCURSEL = 0
1.27 1.7 2.13 mA
Ih(max)
charge pump high, maximum
current
CPHIGH = 1 and CPCURSEL = 1
1.87 2.5 3.13 mA
I2C-bus and PORTn
SDA and SCL input
VIL
LOW-level input voltage
VIH
HIGH-level input voltage
IHI
HIGH-level leakage current
ILI
LOW-level leakage current
fSCL
input clock frequency
SDA output
5 V and 3.3 V bus
5 V and 3.3 V bus
VIH = 3.3 V; VCC = 0 V or 3.3 V
VIL = 0 V; VCC = 3.3 V
-
-
2.3 -
-
-
−10 -
-
-
0.99 V
-
V
10
µA
-
µA
400 kHz
VO
AS input
output voltage during acknowledge Isink = 3 mA
-
-
0.4 V
IASh
IASl
PORTn
high level input current
low level input current
VAS = VCC
VAS = 0 V
−100 -
−100 -
+100 µA
+100 µA
VO(max)
PORTn maximum output voltage Isink = 9 mA
-
-
0.4 V
[1] The product is qualified with an output voltage of 550 mV (p-p) differential, however larger values can be used at baseband outputs that
might have impact on the product performance.
[2] IIP2 = −20 + (P1 − P2) [dBm].
Wanted signal: RF1 is 2140 MHz, PRFIN = −20 dBm and the AGC adjusted to get 550 mV (p-p) on the differential output. The output level
is P1.
9397 750 13193
Product data sheet
Rev. 01 — 14 December 2004
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
21 of 28
Share Link: 