MC33991DW データシートの表示（PDF） - Freescale Semiconductor

部品番号

コンポーネント説明

メーカー

MC33991DW

Gauge Driver Integrated Circuit

Freescale Semiconductor 

TIMING DESCRIPTIONS AND DIAGRAMS

COMMUNICATION MEMORY MAPS

These bits are write-only.

P0 12—This bit must be transmitted as logic[0] for valid

commands.

P0 11: P00—Desired pointer position of Gauge 1.

Pointer positions can range from 0 (000000000000) to

position 4095 (111111111111). For a stepper motor requiring

12 microsteps per degree of pointer movement, the

maximum pointer sweep is 341.25°.

Gauge Return to Zero Register (RTZR)

SI Address 100—Gauge Return to Zero Register (RTZR),

provided in Table 7, is written to return the gauge pointers to

the zero position. During an RTZ event, the pointer is

returned to zero using full steps where only one coil is driven

at any point in time. The back ElectroMotive Force (EMF)

signal present on the non-driven coil is integrated; its results

are stored in an accumulator. Contents of this register’s 15-

bit RTZ accumulator can be read eight bits at a time.

A logic [1] written to bit D1 enables a Return to Zero for

Gauge 0 if D0 is logic [0], and Gauge 1 if D0 is 1, respectively.

Similarly, a logic [0] written to bit D1 disables a Return to Zero

for Gauge 0 when D0 is logic [0], and Gauge 1 when D0 is 1,

respectively.

Bits D3 and D2 are used to determine which eight bits of

the 15-bit RTZ accumulator are clocked out of the SO register

as the 8 MSBs of the SO word. See Table 12. This feature

provides the flexibility to look at 15 bits of content with eight

bits of the SO word. This 8-bit window can be dynamically

changed while in the RTZ mode.

A logic [00], written to bits D3:D2, results in the RTZ

accumulator bits 7:0, clocked out as SO bits D15:D8

respectively. Similarly, a logic [01] results in RTZ counter bits

11:4 clocked out and logic [10] delivers counter bits 14:8 as

SO bits D14:D8 respectively. A logic [11] clocks out the

same information as logic [10]. This feature allows the master

to monitor the RTZ information regardless the size of the

signal. Further, this feature is very useful during the

determination of the accumulator offset to be loaded in for a

motor and pointer combination. It should be noted, RTZ

accumulator contents will reflect the data from the previous

step. The first accumulator results to be read back during the

first step will be 1111111111111111.

Bits D12:D5 must be at logic [0] for valid RTZR

commands.

Bit D4 is used to enable an unconditional RTZ event. A

logic [0] results in a typical RTZ event automatically stopping

when a stall condition is detected. A logic [1] results in RTZ

movement, stopping only if a logic [0] is written to bit D0. This

feature is useful during development and characterization of

RTZ requirements.

The register bits in Table 7 are write-only.

Table 10. Return to Zero Register (RTZR)

D12

D11

D10

D9

Address: 100

D8

D7

D6

D5

D4

D3

D2

D1

D0

Write

0

0

0

0

0

0

Table 11. RTZ Accumulator Bit Select

D3

D2

RTZ Accumulator Bits To SO Bits

ST15:ST8

0

0

[7:0]

0

1

[11:4]

1

0

[14:8]

1

1

[14:8]

RZ12:RZ5— These bits must be transmitted as logic [0] for

valid commands.

RZ4—This bit is used to enable an unconditional RTZ

event.

• 0 = Automatic Return to Zero

• 1 = Unconditional Return to Zero

RZ3:RZ2— These bits are used to determine which eight

bits of the RTZ accumulator will be clocked out via the SO pin.

See Table 8.

RZ1—Return to Zero commands the selected gauge to

return the pointer to zero position.

• 0 = Return to Zero Disabled

• 1 = Return to Zero Enabled

0

0

RZ4 RZ3 RZ2 RZ1 RZ0

RZ0—Gauge Select: Gauge 0/Gauge 1selects the gauge

to be commanded.

• 0 = Selects Gauge 0

• 1 = Selects Gauge 1

GAUGE RETURN TO ZERO CONFIGURATION

REGISTER

SI Address 101—Gauge Return to Zero Configuration

Register (RTZCR) is used to configure the Return to Zero

Event. See Table 9. It is written to modify the step time, or

rate; the pointer moves during an RTZ event. Also, the

integration blanking time is adjustable with this command.

Integration blanking time is the time immediately following the

transition of a coil from a driven state to an open state in the

RTZ mode. Finally, this command is used to adjust the

threshold of the RTZ integration register.

The values used for this register will be chosen during

development to optimize the RTZ for each application.

Various resonance frequencies can occur due to the

interaction between the motor and the pointer. This

command permits moving the RTZ pointer speed away from

these frequencies.

Bits D3: D0 determine the time spent at each full step

during an RTZ event. The step time associated with each bit

33991

16

Analog Integrated Circuit Device Data

Freescale Semiconductor

Share Link: