MT89L85AN データシートの表示（PDF） - Mitel Networks

部品番号

コンポーネント説明

メーカー

MT89L85AN

CMOS ST-BUS™ FAMILY Enhanced Digital Switch

Mitel Networks 

MT89L85

Advance Information

description, the address input lines and the Stream

Address bits (STA) of the Control register give the

user the capability of selecting all positions of the

MT89L85 Data and Connect memories.

The data in the Control register consists of Split

memory and Message mode bits, Memory select and

Stream Address bits (see Figure 4). The memory

select bits allow the Connect Memory HIGH or LOW

or the Data Memory to be chosen, and the Stream

Address bits define an internal memory subsections

corresponding to input or output ST-BUS streams.

Bit 7 (Split Memory) of the Control register allows

split memory operation whereby reads are from the

Data memory and writes are to the Connect Memory

LOW.

The Message Enable bit (bit 6) places every output

channel on every output stream in message mode;

i.e., the contents of the Connect Memory LOW

(CML) are output on the ST-BUS output streams

once every frame unless the ODE input pin is LOW.

If ME bit is HIGH, then the MT89L85 behaves as if

bits 2 (Message Channel) and 0 (Output Enable) of

every Connect Memory HIGH (CMH) locations were

set to HIGH, regardless of the actual value. If ME bit

is LOW, then bit 2 and 0 of each Connect Memory

HIGH location operates normally. In this case, if bit 2

of the CMH is HIGH, the associated ST-BUS output

channel is in Message mode. If bit 2 of the CMH is

LOW, then the contents of the CML define the source

information (stream and channel) of the time slot that

is to be switched to an output.

If the ODE input pin is LOW, then all serial outputs

are high-impedance. If ODE is HIGH, then bit 0

(Output Enable) of the CMH location enables (if

HIGH) or disables (if LOW) the output drivers for the

corresponding individual ST-BUS output stream and

channel.

The contents of bit 1 (CSTo) of each Connection

Memory High location (see Figure 5) is output on

CSTo pin once every frame. The CSTo pin is a 2048

Mbit/s output which carries 256 bits. If CSTo bit is set

HIGH, the corresponding bit on CSTo output is

transmitted in HIGH. If CSTo bit is LOW, the

corresponding bit on the CSTo output is transmitted

in LOW. The contents of the 256 CSTo bits of the

CMH are transmitted sequentially on to the CSTo

output pin and are synchronous to the ST-BUS

streams. To allow for delay in any external control

7

6

SM ME

5

4

3

2

1

0

X

MS1 MS0 STA2 STA1 STA0

BIT

NAME

DESCRIPTION

7

SM

6

ME

4-3 MS1-MS0

2-0

STA2-0

x = Don’t care

Split Memory. When 1, all subsequent reads are from the Data Memory and writes are to

the Connection Memory Low, except when the Control Register is accessed again. The

Memory Select bits need to be set to specify the memory for the operations. When 0, the

Memory Select bits specify the memory for subsequent operations. In either case, the

Stream Address Bits select the subsection of the memory which is made available.

Message Enable. When 1, the contents of the Connection Memory Low are output on the

Serial Output streams except when in High Impedance. When 0, the Connection Memory

bits for each channel determine what is output.

Memory Select Bits. The memory select bits operate as follows:

0-0 - Not to be used

0-1 - Data Memory (read only from the CPU)

1-0 - Connection Memory Low

1-1 - Connection Memory High

Stream Address Bits 2-0. The number expressed in binary notation on these bits refers to

the input or output ST-BUS stream which corresponds to the subsection of memory made

accessible for subsequent operations.

Figure 4 - Control Register Bits

6

Share Link: