TS5070 データシートの表示（PDF） - STMicroelectronics

部品番号

コンポーネント説明

メーカー

TS5070

PROGRAMMABLE CODEC/FILTER COMBO 2ND GENERATION

STMicroelectronics 

Alternatively, the internal time-slot assignment

counters and comparators can be used to access

any time-slot in a frame, using the frame sync inputs

as marker pulses for the beginning of transmit and

receive time-slot 0. In this mode, a frame may con-

sist of up to 64 time-slots of 8 bits each. A time-slot

is assigned by a 2-byte instruction as shown in table

1 and 6. The last 6 bits of the second byte indicate

the selected time-slot from 0-63 using straight bi-

nary notation. A new assignment becomes active

on the second frame following the end of the Chip

Select for the second control byte. The "EN" bit al-

lows the PCM inputs DR0/1 or outputs DX0/1 as ap-

propriate, to be enabled or disabled.

Time-Slot Assignment mode requires that the FSX

and FSR pulses must conform to the delayed timing

format shown in figure 6.

PORT SELECTION

On the TS5070 only, an additional capability is

available : 2 Transmit serial PCM ports, DX0 and

DX1, and 2 receive serial PCM ports, DR0 and DR1,

are provided to enable two-way space switching to

be implemented. Port selections for transmit and

receive are made within the appropriate time-slot

Table 7: Byte 2 of Transmit Gain Instructions.

Bit Number

76543210

00000000

00000001

00000010

10111111

11111110

11111111

(*) State at power initialization

RECEIVE GAIN INSTRUCTION BYTE 2

The receive gain can be programmed in 0.1 dB

steps by writing to the Receive Gain Register as de-

fined in table 1 and 8. Note the following restriction

on output drive capability :

a) 0 dBm0 levels ≤ 8.1dBm at VFRO may be

driven into a load of ≥ 15 kΩ to GND,

b) 0 dBm0 levels ≤ 7.6dBm at VFRO may be

driven into a load of ≥ 600 Ω to GND,

c) 0 dBm levels ≤ 6.9dBm at VFRO may be driven

TS5070 - TS5071

assignment instruction using the "PS" bit in the sec-

ond byte.

On the TS5071, only ports DX0 and DR0 are avail-

able, therefore the "PS" bit MUST always be set to

0 for these devices.

Table 6 shows the format for the second byte of

both transmit and receive time-slot and port assign-

ment instructions.

TRANSMIT GAIN INSTRUCTION BYTE 2

The transmit gain can be programmed in 0.1 dB

steps by writing to the Transmit Gain Register as

defined in tables 1 and 7. This corresponds to a

range of 0 dBm0 levels at VFXI between 1.619

Vrms and 0.087 Vrms (equivalent to + 6.4 dBm to

– 19.0 dBm in 600 Ω).

To calculate the binary code for byte 2 of this in-

struction for any desired input 0 dBm0 level in

Vrms, take the nearest integer to the decimal

number given by :

200 X log10 (V/√6 ) + 191

and convert to the binary equivalent. Some exam-

ples are given in table 7.

0dBm0 Test Leve at VFXI

In dBm (Into 600Ω)

In Vrms (approx.)

No Output

– 19

– 18.9

0.087

0.088

0

0.775

+6.3

1.60

+6.4

1.62

into a load of ≥ 300 Ω to GND.

To calculate the binary code for byte 2 of this in-

struction for any desired output 0 dBm0 level in

Vrms, take the nearest integer to the decimal num-

ber given by :

a

200 X log10 (V/√6 ) + 174

n

d convert to the binary equivalent. Some exam-

ples are given in table 8.

11/32

Share Link: