12020IBZ データシートの表示（PDF） - Intersil

部品番号

コンポーネント説明

メーカー

12020IBZ

Real Time Clock with On Chip Temp Compensation ±5ppm

Intersil 

ISL12020

Serial Data (SDA)

SDA is a bi-directional pin used to transfer data into and out

of the device. It has an open drain output and may be ORed

with other open drain or open collector outputs. The input

buffer is always active (not gated) in normal mode.

An open drain output requires the use of a pull-up resistor.

The output circuitry controls the fall time of the output signal

with the use of a slope controlled pull-down. The circuit is

designed for 400kHz I2C interface speeds. It is disabled

when the backup power supply on the VBAT pin is activated.

VDD, GND

Chip power supply and ground pins. The device will operate

with a power supply from VDD = 2.7V to 5.5VDC. A 0.1µF

capacitor is recommended on the VDD pin to ground.

Functional Description

Power Control Operation

The power control circuit accepts a VDD and a VBAT input.

Many types of batteries can be used with Intersil RTC

products. For example, 3.0V or 3.6V Lithium batteries are

appropriate, and battery sizes are available that can power

the ISL1202x for up to 10 years. Another option is to use a

Super Capacitor for applications where VDD is interrupted

for up to a month. See the “Application Section” on page 22

for more information.

Normal Mode (VDD) to Battery Backup Mode

(VBAT)

To transition from the VDD to VBAT mode, both of the

following conditions must be met:

Condition 1:

VDD < VBAT - VBATHYS

where VBATHYS ≈ 50mV

Condition 2:

VDD < VTRIP

where VTRIP ≈ 2.2V

Battery Backup Mode (VBAT) to Normal Mode

(VDD)

The ISL12020 device will switch from the VBAT to VDD mode

when one of the following conditions occurs:

Condition 1:

VDD > VBAT + VBATHYS

where VBATHYS ≈ 50mV

Condition 2:

VDD > VTRIP + VTRIPHYS

where VTRIPHYS ≈ 30mV

These power control situations are illustrated in Figure 3 and

Figure 4.

VDD

VTRIP

VBAT

VBAT - VBATHYS

BATTERY BACKUP

MODE

2.2V

1.8V

VBAT + VBATHYS

FIGURE 3. BATTERY SWITCHOVER WHEN VBAT < VTRIP

VDD

VBAT

VTRIP

VTRIP

BATTERY BACKUP

MODE

3.0V

2.2V

VTRIP + VTRIPHYS

FIGURE 4. BATTERY SWITCHOVER WHEN VBAT > VTRIP

The I2C bus is deactivated in battery backup mode to reduce

power consumption. Aside from this, all RTC functions are

operational during battery backup mode. Except for SCL and

SDA, all the inputs and outputs of the ISL12020 are active

during battery backup mode unless disabled via the control

register.

The device Time Stamps the switchover from VDD to VBAT

and VBAT to VDD, and the time is stored in TSV2B and

TSB2V registers respectively. If multiple VDD power down

sequences occur before status is read, the earliest VDD to

VBAT power down time is stored and the most recent VBAT

to VDD time is stored.

Temperature conversion and compensation can be enabled

in battery backup mode. Bit BTSE in the BETA register

controls this operation as described in that register section.

Power Failure Detection

Both the ISL12020 provide a Real Time Clock Failure Bit

(RTCF) to detect total power failure. It allows users to

determine if the device has powered up after having lost all

power to the device (both VDD and VBAT).

Brownout Detection

The ISL12020 monitor the VDD level continuously and

provide warning if the VDD level drops below prescribed

levels. There are six (6) levels that can be selected for the

trip level. These values are 85% below popular VDD levels.

The LVDD bit in the Status Register will be set to “1” when

Brownout is detected. Note. The I2C serial bus remains

active unless the Battery Vtrip levels are reached.

8

FN6450.0

March 29, 2007

Share Link: