GLT4116-45J4 データシートの表示（PDF） - G-Link Technology
部品番号
コンポーネント説明
メーカー
GLT4116-45J4 Datasheet PDF : 16 Pages
| |||
GLT41116
ELECTRICAL SPECIFICATIONS
Absolute Maximum Ratings [1]
Parameter
Operating Temperature, TA (ambient)
Storage Temperature (plastic)
Voltage Relative to VSS
Short Circuit Output Current‘
Power Dissipitation
Rating
-0°C to +70°C
-55°C to +125°C
-1.0V to +7.0V
50 mA
1.0 W
1. Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only, and functional operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
Capacitance [1]
Symbol
CIN1
CIN2
COUT
Address Input
RAS, LCAS, UCAS, WE, OE
Data Input/Output
1. Capacitance is sampled and not 100% tested
Parameter
Max
Units
5
pF
7
pF
7
pF
DC Characteristics (TA = 0°C to 70°C, VCC = 5V ± 10%, VSS = 0V, unless otherwise specified)
-30
-35
-40
-45
Symbol
Parameter
Conditions
Min Max Min Max Min Max Min Max Units Notes
ILI
Input Leakage Current 0V ≤ VIN ≤ 5.5V (All other
-10 +10 -10 +10 -10 +10 -10 +10 µA
(any input pin)
pins not under test = 0V)
ILO
Output Leakage Current 0V ≤ VOUT ≤ 5.5V Output is
+10
+10
+10
+10 µA
(for High-Z State)
disabled (Hiz)
ICC1
Operating Current, Ran- tRC = tRC (min.)
dom READ/WRITE
180
170
160
150
mA [1] [2]
ICC2
Standby Current, (TTL) RAS, UCAS, LCAS at VIH
other inputs ≥ VSS
2
2
2
2
mA
ICC3
Refresh Current, RAS- RAS cycling, UCAS, LCAS at
180
170
160
150 mA [2]
Only
VIH tRC = tRC (min.)
ICC4
Operating Current, EDO RAS at VIL, UCAS, LCAS
Page Mode
address cycling: tPC = tPC
(min.)
180
170
160
150
mA [1] [2]
ICC5
Refresh Current, CAS- RAS, UCAS, LCAS address
180
170
160
150 mA [1]
before-RAS
cycling: tRC = tRC (min.)
ICC6
Standby Current,
(CMOS)
VIL
Input Low Voltage
RAS ≥ VCC -0.2V, UCS ≥ VCC
2
2
2
2
mA
-0.2V, LCAS ≥ VCC -0.2V, All
other inputs ≥ VCC
-1
+0.8
-1
+0.8
-1
+0.8
-1
+0.8
V
[3]
VIH
Input High Voltage
2.4 VCC +1 2.4 VCC +1 2.4 VCC +1 2.4 VCC +1 V
VOL
Output Low Voltage
IOL = 4.2 mA
0.4
0.4
0.4
0.4
V
VOH
Output High Voltage
IOH = -5 mA
2.4
2.4
2.4
2.4
V
1. ICC is dependent on output loading when the device output is selected. Specified ICC (max.) is measured with the output open.
2. ICC is dependent upon the number of address transitions specified ICC (max) is measured with a maximum of one transition per address cycle in random READ/WRITE and
Fast-Page Mode.
3. Specified VIL (min) is steady state operation. During transitions VIL (min) may undershoot to -1.0V for a period not to exceed 20 ns. All AC parameter are measured with
VIL (min) ≥ VSS and VIH (max) ≤ VCC.
4
G-LINK Technology
July 1998 (Rev. 1)
Share Link: 