MAX4513CSE(1998) データシートの表示（PDF） - Maxim Integrated
部品番号
コンポーネント説明
メーカー
MAX4513CSE Datasheet PDF : 16 Pages
| |||
Quad, Rail-to-Rail, Fault-Protected,
SPST Analog Switches
ABSOLUTE MAXIMUM RATINGS
(Voltages Referenced to GND)
V+ ........................................................................-0.3V to +44.0V
V- .........................................................................-44.0V to +0.3V
V+ to V-................................................................-0.3V to +44.0V
COM_, IN_ (Note 1) ..............................(V- - 0.3V) to (V+ + 0.3V)
NC_, NO_ (Note 2)..................................(V+ - 36V) to (V- + 36V)
NC_, NO_ to COM_ .................................................-36V to +36V
Continuous Current into Any Terminal..............................±30mA
Peak Current into Any Terminal
(pulsed at 1ms, 10% duty cycle)...................................±50mA
Continuous Power Dissipation (TA = +70°C) (Note 2)
Plastic DIP (derate 10.53mW/°C above +70°C) ...........842mW
Narrow SO (derate 8.70mW/°C above +70°C) .............696mW
CERDIP (derate 10.00mW/°C above +70°C) ................800mW
Operating Temperature Ranges
MAX451_C_ E ......................................................0°C to +70°C
MAX451_E_ E ...................................................-40°C to +85°C
MAX451_MJE .................................................-55°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
Note 1: COM_ and IN_ pins are not fault protected. Signals on COM_ or IN_ exceeding V+ or V- are clamped by internal diodes.
Limit forward diode current to maximum current rating.
Note 2: NC_ and NO_ pins are fault protected. Signals on NC_ or NO_ exceeding -36V to +36V may damage the device. These
limits apply with power applied to V+ or V-, or ±40V with V+ = V- = 0.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—Dual Supplies
(V+ = +15V, V- = -15V, GND = 0V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
ANALOG SWITCH
Fault-Protected Analog
Signal Range
Fault-Free Analog Signal Range
Non-Protected Analog
Signal Range (COM_ Output)
COM_ -NO_ or COM_ -NC_
On-Resistance
SYMBOL
VNO_, VNC_
VNO_, VNC_
VCOM_
RON
CONDITIONS
Applies with power on or off
(Note 2)
Applies with power on or off
(Note 2)
Applies with power on or off
(Note 1)
VCOM_ = ±10V, ICOM_ = 1mA
COM_ -NO_ or COM_ -NC_
On-Resistance Match Between
Channels (Note 4)
∆RON
VCOM_ = ±10V, ICOM_ = 1mA
NO_ or NC_ Off Leakage Current
(Note 5)
INO_(OFF),
INC_(OFF)
VCOM_ = ±14V;
VNO_, VCOM = 14V
COM_ Off Leakage Current
(Note 5)
ICOM_(OFF)
VCOM_ = ±14V;
VNO_, VCOM = 14V
COM_ On Leakage Current
(Note 5)
ICOM_(ON)
VCOM_ = ±14V
TA
MIN TYP MAX
(Note 3)
UNITS
C, E, M -36
36
V
C, E, M
V-
V+
V
C, E, M V- - 0.3
V+ + 0.3 V
+25°C
125 160
C, E
200
Ω
M
250
+25°C
3
6
C, E
10
Ω
M
15
+25°C -0.5 0.01 0.5
C, E
-10
10
nA
M
-200
200
+25°C -0.5 0.01 0.5
C, E
-10
10
nA
M
-200
200
+25°C -0.5 0.01 0.5
C, E
-20
20
nA
M
-400
400
2 _______________________________________________________________________________________
Share Link: 