MAX9012EUA データシートの表示（PDF） - Maxim Integrated
部品番号
コンポーネント説明
メーカー
MAX9012EUA Datasheet PDF : 12 Pages
| |||
SC70, 5ns, Low-Power, Single-Supply,
Precision TTL Comparators
ELECTRICAL CHARACTERISTICS (MAX9012/MAX9013) (continued)
(VCC = 5V, VLE = 0 (MAX9013 only), VCM = 0, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
Small-Signal Voltage Gain
Output Low Voltage
Output High Voltage
Output Short-Circuit Current
SYMBOL
AV
VOL
VOH
IOUT
CONDITIONS
1V ≤ VOUT ≤ 2V
VIN ≥ 100mV
ISINK = 0
ISINK = 4mA
VIN ≥ 100mV,
VCC = 4.5V
ISOURCE = 0
ISOURCE = 4mA
Sinking
Sourcing
MIN
1000
2.7
2.4
TYP
3000
0.3
0.5
3.3
2.9
20
30
MAX
0.5
0.6
UNITS
V/V
V
V
mA
Latch Enable Pin High Input
Voltage
VIH
MAX9013 only
2
V
Latch Enable Pin Low Input
Voltage
VIL
MAX9013 only
0.8
V
Latch Enable Pin Bias Current
Input Noise-Voltage Density
Propagation Delay (Note 6)
Differential Propagation Delay
(Notes 6, 7)
IIH, IIL
en
tPD+, tPD-
∆tPD±
MAX9013 only
VLE = 0 and VLE = 5V
f = 100kHz
CLOAD = 5pF,
TA = +25°C
VOVERDRIVE = 100mV
VOVERDRIVE = 5mV
CLOAD = 5pF,
TA = TMIN to TMAX
VOVERDRIVE = 100mV
VOVERDRIVE = 5mV
VIN = 100mV step, CLOAD = 5pF,
VOD = 5mV
±25
µA
6
nV/√Hz
5
8
5.5
9
ns
9
10
2
3
ns
Channel-to-Channel
Propagation Delay (Note 6)
∆tPD(ch-ch)
MAX9012 only, VIN = 100mV step,
CLOAD = 5pF, VOD = 5mV
500
ps
Output Rise Time
Output Fall Time
Latch Setup Time (Note 8)
Latch Hold Time (Note 8)
tR
0.5V ≤ VOUT ≤ 2.5V
tF
2.5V ≥ VOUT ≥ 0.5V
tSU
MAX9013 only
tH
MAX9013 only
3
ns
2
ns
2
0
ns
2
0.5
ns
Latch Propagation Delay
(Note 8)
tLPD
MAX9013 only
5
ns
Input Capacitance
MAX9012EUA/MAX9013EUA
CIN
MAX9012ESA/MAX9013ESA
1.5
pF
2
Power-Up Time
tON
1
µs
Note 1: All specifications are 100% tested at TA = +25°C; temperature limits are guaranteed by design.
Note 2: Quiescent Power-Supply Current is slightly higher with the comparator output at VOL. This parameter is specified with the worst-
case condition of VOUT = VOL for the MAX9010/MAX9011 and both outputs at VOL for the MAX9012. For the MAX9013, which
has complementary outputs, the power-supply current is specified with either OUT = VOL, OUT = VOH or OUT = VOH, OUT =
VOL (power-supply current is equal in either case).
Note 3: Input Offset Voltage is tested and specified with the Input Common-Mode Voltage set to either extreme of the Input Common-
Mode Voltage Range (-0.2V to (VCC - 1.9V)) and with the Power-Supply Voltage set to either extreme of the Power-Supply
Voltage Range (4.5V to 5.5V).
4 _______________________________________________________________________________________
Share Link: 