A7B データシートの表示（PDF） - AnaSem Semiconductors

部品番号

コンポーネント説明

メーカー

A7B

Single-cell Li-ion / Li-polymer Battery Protection IC

AnaSem Semiconductors 

Rev. E09-06

Single-cell Li-ion / Li-polymer Battery Protection IC

A7B Series

z DO : Pch ON resistance, DO : Nch ON resistance --- [Circuit 5]

Set V1=3.5V, V2=0V and V4=3.0V. (V1-V4)/|IDO| is Pch ON resistance Rdop.

Set V1=V2=1.8V and V4=0.5V. V4/|IDO| is Nch ON resistance Rdon.

z Discharge over-current release resistance --- [Circuit 5]

Set V1=3.5V, V2=0V at first. And then, set V2=1.0V. V2/|IVM| is discharge over-current release resistance Rdwn.

z Over-charge detection delay time, Release delay time 2 --- [Circuit 6]

Set V2=0V. Increase V1 from the voltage Vc-0.2V to Vc+0.2V rapidly within 10μs. Over-charge detection

delay time tc is the time needed for VCO to go "Low" just after the change of V1.

Next, set V2=1V and decrease V1 from Vc+0.2V to Vc-0.2V rapidly within 10μs. Over-charge release delay

time trel 2 is the time needed for VCO to go "High" just after the change of V1.

z Over-discharge detection delay time, Release delay time 1 --- [Circuit 6]

Set V2=0V. Decrease V1 from the voltage Vdc+0.2V to Vdc-0.2V rapidly within 10μs. Over-discharge

detection delay time tdc is the time needed for VDO to go "Low" just after the change of V1.

Next, set V2=-1V and increase V1 from Vdc-0.2V to Vdc+0.2V rapidly within 10μs. Release delay time 1 trel1 in

case of over-discharge is the time needed for VDO to go "High" just after the change of V1.

z Charge over-current detection delay time, Release delay time 1 --- [Circuit 6]

Set V1=3.5V and V2=0V. Decrease V2 from 0V to -1V rapidly within 10μs. Charge over-current delay time tic

is the time needed for VCO to go "Low" just after the change of V2.

Next, increase V2 from -1V to 0V rapidly within 10μs. Release delay time 1 trel1 in case of charge over-current

is the time needed for VCO to go "High" just after the change of V2.

z Discharge over-current detection delay time, Release delay time 1 --- [Circuit 6]

Set V1=3.5V and V2=0V. Increase V2 from 0V to 1V rapidly within 10μs. Discharge over-current delay time

tidc is the time needed for VDO to go "Low" just after the change of V2.

Next, decrease V2 from 1V to 0V rapidly within 10μs. Release delay time 1 trel1 in case of discharge over-

current is the time needed for VDO to go "High" just after the change of V2.

z Load short-circuiting detection delay time, Release delay time 1 --- [Circuit 6]

Set V1=3.5V and V2=0V. Increase V2 from 0V to 3.5V rapidly within 10μs. Load short-circuiting detection

delay time tshort is the time needed for VDO to go "Low" just after the change of V2. Next, decrease V2 from

3.5V to 0V rapidly within 10μs. Release delay time 1 trel1 in case of load short-circuiting is the time needed for

VDO to go "High" just after the change of V2.

AnaSem Inc.

7

.......... Future of the analog world

Share Link: