CAT25C03U14ATE13 データシートの表示（PDF） - Catalyst Semiconductor => Onsemi
部品番号
コンポーネント説明
メーカー
CAT25C03U14ATE13 Datasheet PDF : 12 Pages
| |||
CAT25C11/03/05/09/17
ABSOLUTE MAXIMUM RATINGS*
Temperature Under Bias ................. –55°C to +125°C
Storage Temperature ....................... –65°C to +150°C
Voltage on any Pin with
Respect to VSS(1) .................. –2.0V to +VCC +2.0V
VCC with Respect to VSS ................................ –2.0V to +7.0V
Package Power Dissipation
Capability (Ta = 25°C) ................................... 1.0W
Lead Soldering Temperature (10 secs) ............ 300°C
Output Short Circuit Current(2) ........................ 100 mA
RELIABILITY CHARACTERISTICS
Symbol
NEND(3)
TDR(3)
VZAP(3)
ILTH(3)(4)
Parameter
Endurance
Data Retention
ESD Susceptibility
Latch-Up
Min.
1,000,000
100
2000
100
Max.
*COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
These are stress ratings only, and functional operation
of the device at these or any other conditions outside of
those listed in the operational sections of this specifica-
tion is not implied. Exposure to any absolute maximum
rating for extended periods may affect device perfor-
mance and reliability.
Units
Cycles/Byte
Years
Volts
mA
Reference Test Method
MIL-STD-883, Test Method 1033
MIL-STD-883, Test Method 1008
MIL-STD-883, Test Method 3015
JEDEC Standard 17
D.C. OPERATING CHARACTERISTICS
VCC = +1.8V to +6.0V, unless otherwise specified.
Limits
Symbol
Parameter
Min. Typ.
Max.
Units
Test Conditions
ICC1
Power Supply Current
(Operating Write)
5
mA VCC = 5V @ 5MHz
SO=open; CS=Vss
ICC2
ISB(6)
Power Supply Current
(Operating Read)
Power Supply Current
(Standby)
3
mA VCC = 5.5V
FCLK = 5MHz
1
µA CS = VCC
VIN = VSS or VCC
ILI
Input Leakage Current
ILO
Output Leakage Current
2
µA
3
µA VOUT = 0V to VCC,
CS = 0V
VIL(5)
VIH(5)
Input Low Voltage
Input High Voltage
-1
VCC x 0.7
VCC x 0.3
V
VCC + 0.5
V
VOL1
VOH1
Output Low Voltage
Output High Voltage
VCC - 0.8
0.4
V
2.7V≤VCC<5.5V
V
IOL = 3.0mA
IOH = -1.6mA
VOL2
VOH2
Output Low Voltage
Output High Voltage
VCC-0.2
0.2
V 1.8V≤VCC<2.7V
V
IOL = 150µA
IOH = -100µA
Note:
(1) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC
voltage on output pins is VCC +0.5V, which may overshoot to VCC +2.0V for periods of less than 20 ns.
(2) Output shorted for no more than one second. No more than one output shorted at a time.
(3) This parameter is tested initially and after a design or process change that affects the parameter.
(4) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1V to VCC +1V.
(5) VILMIN and VIHMAX are reference values only and are not tested.
(6) Maximum standby current (ISB ) = 10µA for the Automotive and Extended Automotive temperature range.
Doc. No. 1017, Rev. J
2
Share Link: 