DatasheetQ Logo
Electronic component search and free download site. Transistors,MosFET ,Diode,Integrated circuits

48SD3208 データシートの表示(PDF) - MAXWELL TECHNOLOGIES

部品番号
コンポーネント説明
メーカー
48SD3208
Maxwell
MAXWELL TECHNOLOGIES Maxwell
48SD3208 Datasheet PDF : 39 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
256Mb (8-Meg X 8-Bit X 4-Banks) SDRAM
48SD3208
TABLE 4. DC ELECTRICAL CHARACTERISTICS
(VCC = 3.3V + 0.3V, VCCQ = 3.3V + 0.3V, TA = -55 TO 125°C, UNLESS OTHERWISE SPECIFIED)
PARAMETER
SYMBOL
TEST CONDITIONS
SUBGROUPS MIN
MAX
Standby Current in Power Down
ICC2PS
CKE = VIL
1, 2, 3
2
( input signal stable)5
tCK = 0
UNITS
mA
Standby Current in non power down6
Standby Current in non power down
( Input signal stable)7
Active standby current in
power down1, 2, 4
Active standby current in power down
(input signal stable)2, 5
Active standby power in
non power down1,2, 6
Active standby current in non power
down ( input signal stable)2,7
Burst Operating Current11,2,8
CAS Latency = 2
CAS Latency = 3
ICC2N
ICC2NS
ICC3P
ICC3PS
ICC3N
ICC3NS
ICC4
CKE, CS = VIH
tCK = 12 ns
CKE = VIH
tCK = 0
CKE = VIL
tCK = 12 ns
CKE = VIL
tCK = 0
CKE, CS = VIH
tCK = 12 ns
CKE = VIH
tCK = 0
tCK = min
BL = 4
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
20
mA
9
mA
4
mA
3
mA
30
mA
15
mA
mA
110
145
Refresh Current3
ICC5
tRC = min
1, 2, 3
220 mA
Self Refresh current9
ICC6
VIH>VCC - 0.2V
1, 2, 3
VIL < 0.2 V
3
mA
Input Leakage Current
ILI
0<VIN<VCC
1, 2, 3
-1
1
uA
Output Leakage Current
ILO
0<VOUT<VCC
1, 2, 3 -1.5
1.5
uA
Output high voltage
VOH
IOH = -4mA
1, 2, 3 2.4
V
Output low voltage
VOL
IOL = 4 mA
1, 2, 3
0.4
V
1. ICC1 depends on output load conditions when the device is selected. ICC1 (max) is specified with the output open.
2. One bank operation.
3. Input Signals are changed once per one clock.
4. After power down mode, CLK operating current.
5. After power down mode, no CLK operating current.
6. Input signals are changed once per two clocks.
7. Input signals are VIH or VIL fixed.
8. Input signals are changed once per four clocks.
9. After self refresh mode set, self refresh current. Self refresh mode Should be used at temperatures below 70 °C
01.10.05 Rev 2
All data sheets are subject to change without notice 4
©2005 Maxwell Technologies
All rights reserved.

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]