74ALVT16244 データシートの表示（PDF） - Philips Electronics
部品番号
コンポーネント説明
メーカー
74ALVT16244 Datasheet PDF : 10 Pages
| |||
Philips Semiconductors
2.5V/3.3V 16-bit buffer/driver (3-State)
Product specification
74ALVT16244
RECOMMENDED OPERATING CONDITIONS
SYMBOL
PARAMETER
VCC
VI
VIH
VIL
IOH
IOL
∆t/∆v
Tamb
DC supply voltage
Input voltage
High-level input voltage
Input voltage
High-level output current
Low-level output current
Low-level output current; current duty cycle ≤ 50%; f ≥ 1kHz
Input transition rise or fall rate; Outputs enabled
Operating free-air temperature range
2.5V RANGE LIMITS
MIN
MAX
2.3
2.7
0
5.5
1.7
0.7
–8
8
24
10
–40
+85
3.3V RANGE LIMITS
MIN
MAX
3.0
3.6
0
5.5
2.0
0.8
–32
32
64
10
–40
+85
UNIT
V
V
V
V
mA
mA
ns/V
°C
DC ELECTRICAL CHARACTERISTICS (3.3V "0.3V RANGE)
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
Temp = -40°C to +85°C UNIT
MIN TYP1 MAX
VIK
Input clamp voltage
VCC = 3.0V; IIK = –18mA
–0.85 –1.2
V
VOH
High-level output voltage
VCC = 3.0 to 3.6V; IOH = –100µA
VCC = 3.0V; IOH = –32mA
VCC–0.2 VCC
V
2.0
2.3
VCC = 3.0V; IOL = 100µA
0.07 0.2
VOL
Low–level output voltage
VCC = 3.0V; IOL = 16mA
VCC = 3.0V; IOL = 32mA
0.25 0.4
V
0.3 0.5
VCC = 3.0V; IOL = 64mA
0.4 0.55
VCC = 3.6V; VI = VCC or GND
Control pins
0.1
±1
II
Input leakage current
VCC = 0 or 3.6V; VI = 5.5V
VCC = 3.6V; VI = VCC
VCC = 3.6V; VI = 0V
Data pins4
01.
10
µA
0.5
1
0.1
-5
IOFF
Off current
VCC = 0V; VI or VO = 0 to 4.5V
0.1 ±100 µA
IHOLD
Bus Hold current
Data inputs6
VCC = 3V; VI = 0.8V
VCC = 3V; VI = 2.0V
VCC = 0V to 3.6V; VCC = 3.6V
75
130
–75 –140
µA
±500
IEX
Current into an output in the
High state when VO > VCC
VO = 5.5V; VCC = 3.0V
10
125
µA
IPU/PD
Power up/down 3-State output VCC ≤ 1.2V; VO = 0.5V to VCC; VI = GND or VCC
current3
OE/OE = Don’t care
1
±100 µA
IOZH 3-State output High current
VCC = 3.6V; VO = 3.0V; VI = VIL or VIH
0.5
5
µA
IOZL
3-State output Low current
VCC = 3.6V; VO = 0.5V; VI = VIL or VIH
0.5
–5
µA
ICCH
VCC = 3.6V; Outputs High, VI = GND or VCC, IO = 0
0.05 0.1
ICCL
ICCZ
Quiescent supply current
VCC = 3.6V; Outputs Low, VI = GND or VCC, IO = 0
VCC = 3.6V; Outputs Disabled; VI = GND or VCC, IO = 05
3.6
5
mA
0.06 0.1
∆ICC
Additional supply current per
input pin2
VCC = 3V to 3.6V; One input at VCC–0.6V,
Other inputs at VCC or GND
0.04 0.4 mA
NOTES:
1. All typical values are at VCC = 3.3V and Tamb = 25°C.
2. This is the increase in supply current for each input at the specified voltage level other than VCC or GND
3. This parameter is valid for any VCC between 0V and 1.2V with a transition time of up to 10msec. From VCC = 1.2V to VCC = 3.3V ± 0.3V a
transition time of 100µsec is permitted. This parameter is valid for Tamb = 25°C only.
4. Unused pins at VCC or GND.
5. ICCZ is measured with outputs pulled up to VCC or pulled down to ground.
6. This is the bus hold overdrive current required to force the input to the opposite logic state.
1998 Oct 07
4
Share Link: 