ACS716 データシートの表示（PDF） - Allegro MicroSystems

部品番号

コンポーネント説明

メーカー

ACS716

120 kHz Bandwidth, High Voltage Isolation Current Sensor with Integrated Overcurrent Detection

Allegro MicroSystems 

ACS716

120 kHz Bandwidth, High Voltage Isolation

Current Sensor with Integrated Overcurrent Detection

COMMON OPERATING CHARACTERISTICS Valid at TA = –40°C to 125°C, VCC = 3.3 V, unless otherwise specified

Characteristic

Symbol

Test Conditions

Min.

Typ.

ELECTRICAL CHARACTERISTICS

Supply Voltage

Nominal Supply Voltage

Supply Current

Output Capacitance Load

Output Resistive Load

Magnetic Coupling from Device Conductor

to Hall Element

VCC

VCCN

ICC

CLOAD

RLOAD

MCHALL

VIOUT open, ¯F¯¯A¯U¯¯L¯¯T¯ pin high

VIOUT pin to GND

VIOUT pin to GND

Current flowing from IP+ to IP– pins

3

–

–

3.3

–

9

–

–

10

–

–

9.5

Internal Filter Resistance1

RF(INT)

Primary Conductor Resistance

RPRIMARY

ANALOG OUTPUT SIGNAL CHARACTERISTICS

TA = 25°C

–

1.7

–

1

Full Range Linearity2

Symmetry3

ELIN

ESYM

IP = ±IP0A

IP = ±IP0A

–0.75

99.1

±0.25

100

Bidirectional Quiescent Output

VOUT(QBI)

TIMING PERFORMANCE CHARACTERISTICS

IP = 0 A, TA = 25°C

–

VCC×0.5

VIOUT Signal Rise Time

TA = 25°C, Swing IP from 0 A to IP0A,

tr

no capacitor on FILTER pin, 100 pF from

–

3

VIOUT to GND

VIOUT Signal Propagation Time

tPROP

TA = 25°C, no capacitor on FILTER pin,

100 pF from VIOUT to GND

–

1

VIOUT Signal Response Time

TA = 25°C, Swing IP from 0 A to IP0A,

tRESPONSE no capacitor on FILTER pin, 100 pF from

–

4

VIOUT to GND

VIOUT Large Signal Bandwidth

–3 dB, Apply IP such that VIOUT = 1 Vpk-pk,

f3dB

no capacitor on FILTER pin, 100 pF from

–

120

VIOUT to GND

Power-On Time

OVERCURRENT CHARACTERISTICS

tPO

Output reaches 90% of steady-state level,

no capacitor on FILTER pin, TA = 25°C

–

35

Setting Voltage for Overcurrent Switchpoint4

Signal Noise at Overcurrent

Comparator Input

VOC

INCOMP

VCC×0.25

–

–

±1

Overcurrent Fault Switchpoint Error5,6

EOC

Switchpoint in VOC safe operating area;

assumes INCOMP = 0 A

–

±5

Overcurrent ¯F¯¯A¯U¯¯L¯¯T¯ Pin Output Voltage

V ¯F¯ ¯A¯U¯¯L¯ ¯T¯

1 mA sink current at ¯F¯¯A¯U¯¯L¯¯T¯ pin

–

–

Fault Enable (FAULT_EN Pin) Input Low

Voltage Threshold

VIL

–

–

Max. Units

3.6

V

–

V

11

mA

10

nF

–

kΩ

–

G/A

–

kΩ

–

mΩ

0.75

%

100.9 %

–

V

–

μs

–

μs

–

μs

–

kHz

–

μs

VCC×0.4 V

–

A

–

%

0.4

V

0.1 × VCC V

Continued on the next page…

Allegro MicroSystems, LLC

6

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

Share Link: