AD1858 データシートの表示（PDF） - Analog Devices
部品番号
コンポーネント説明
メーカー
AD1858 Datasheet PDF : 16 Pages
| |||
AD1857/AD1858
PIN LIST
Digital Audio Serial Input Interfaces
Pin Name
Number
I/O
SDATA
20
I
BCLK
19
I
LRCLK
18
I
MODE
3
I
Description
Serial input, MSB first, containing two channels of 16, 18 or 20 bits (AD1857) or
16 bits (AD1858) of twos complement data per channel.
Bit clock input for input data. Need not run continuously; may be gated or used in a
burst fashion.
Left/right clock input for input data. Must run continuously.
Input serial data port mode control. Selects between I2S-justified (HI) and left-justified
(LO) on the AD1857. Selects between DSP serial port style mode (HI) and right-
justified (LO) on the AD1858. The state of the mode pin should be changed only when
the AD1857/AD1858 is held in reset (PD/RST LO). Otherwise, the AD1857/
AD1858 serial port may lose synchronism.
Control and Clock Signals
Pin Name
Number
I/O
Description
PD/RST
2
DEEMP
5
MUTE
15
MCLK
1
384/256
6
I
Power-Down/Reset. The AD1857/AD1858 are placed in a low power consumption
“sleep” mode when this pin is held LO. The AD1857/AD1858 are reset on the
rising edge of this signal. Connect HI for normal operation.
I
De-emphasis. Digital de-emphasis is enabled when this input signal is HI. This is
used to impose a 50/15 µs response characteristic on the output audio spectrum at
an assumed 44.1 kHz sample rate.
I
Mute. Assert HI to mute both stereo analog outputs of the AD1857/AD1858.
Deassert LO for normal operation.
I
Master Clock Input. Connect to an external clock source at either 256 or 384 times
the intended sample frequency as determined by the 384/256 pin. Must be synchro-
nous with LRCLK, but may have any phase with respect to LRCLK.
I
Selects the master clock mode as either 384 times the intended sample frequency
(HI) or 256 times the intended sample frequency (LO). The state of this input
should be hardwired to logic LO or logic HI or may be changed while the AD1857/
AD1858 is in power-down/reset. It must not be changed while the AD1857/AD1858
is operational.
Analog Signals
Pin Name
Number
I/O
Description
FILT
11
CMOUT
10
OUTL
8
OUTR
13
O
Voltage Reference Filter Capacitor Connection. Bypass and decouple the voltage
reference with parallel 10 µF and 0.1 µF capacitors to the AGND pin.
O
Voltage Reference Common Mode Output. Should be decoupled with 10 µF
capacitor to the AGND pin or plane. This output is available externally for dc
coupling and level-shifting. CMOUT should not have any signal dependent load,
or used where it will sink or source current.
O
Left channel line level analog output.
O
Right channel line level analog output.
Power Supply Connections and Miscellaneous
Pin Name
Number
I/O
Description
AVDD
AGND
DVDD
DGND
N/C
7, 14
9, 12
17
16
4
I
Analog Power Supply. Connect to analog +5 V supply.
I
Analog Ground.
I
Digital Power Supply. Connect to digital +5 V supply.
I
Digital Ground.
No Connect. Reserved. Do not connect.
REV. 0
–5–
Share Link: 