AD7495BRM-REEL データシートの表示（PDF） - Analog Devices

部品番号

コンポーネント説明

メーカー

AD7495BRM-REEL

1 MSPS, 12-Bit ADCs

Analog Devices 

TERMINOLOGY

Integral Nonlinearity

The maximum deviation from a straight line passing through

the endpoints of the ADC transfer function. The endpoints of

the transfer function are zero scale, a point ½ LSB below the

first code transition, and full scale, a point ½ LSB above the last

code transition.

Differential Nonlinearity

The difference between the measured and the ideal 1 LSB

change between any two adjacent codes in the ADC.

Offset Error

The deviation of the first code transition (00 . . . 000) to

(00 . . . 001) from the ideal, that is, AGND + 0.5 LSB.

Gain Error

This is the deviation of the last code transition (111. . . 110) to

(111. . . 111) from the ideal (that is, VREF − 1.5 LSB) after the

offset error has been adjusted out.

Track-and-Hold Acquisition Time

The track-and-hold amplifier returns into track mode on the

13th SCLK rising edge (see the Serial Interface section). The

track-and-hold acquisition time is the minimum time required

for the track-and-hold amplifier to remain in track mode for its

output to reach and settle to within 0.5 LSB of the applied input

signal, given a step change to the input signal.

Signal-to-Noise and Distortion Ratio (SINAD)

The measured ratio of signal-to-noise and distortion at the

output of the analog-to-digital converter (ADC). The signal is

the rms amplitude of the fundamental. Noise is the sum of all

nonfundamental signals up to half the sampling frequency

(fS/2), excluding dc. The ratio is dependent on the number of

quantization levels in the digitization process; the more levels,

the smaller the quantization noise. The theoretical SINAD ratio

for an ideal N-bit converter with a sine wave input is given by

Signal to (Noise + Distortion) = (6.02 N + 1.76) dB

For a 12-bit converter, the SINAD is 74 dB.

AD7475/AD7495

Total Harmonic Distortion (THD)

The ratio of the rms sum of harmonics to the fundamental. For

the AD7475/AD7495, THD is defined as

THD (dB) = 20 log V22 + V32 + V42 + V52 +V6 2

V1

where V1 is the rms amplitude of the fundamental and V2, V3,

V4, V5, and V6 are the rms amplitudes of the second through the

sixth harmonics.

Peak Harmonic or Spurious Noise

The ratio of the rms value of the next largest component in

the ADC output spectrum (up to fS/2 and excluding dc) to

the rms value of the fundamental. Normally, the value of this

specification is determined by the largest harmonic in the

spectrum, but for ADCs where the harmonics are buried in

the noise floor, it is a noise peak.

Intermodulation Distortion

With inputs consisting of sine waves at two frequencies, fa and

fb, any active device with nonlinearities creates distortion

products at sum and difference frequencies of mfa ± nfb where

m, n = 0, 1, 2, 3, etc. Intermodulation distortion terms are those

for which neither m nor n is equal to zero. For example, the

second-order terms include (fa + fb) and (fa − fb), while the

third-order terms include (2fa + fb), (2fa − fb), (fa + 2fb), and

(fa − 2fb).

The AD7475/AD7495 are tested using the CCIF standard where

two input frequencies near the top end of the input bandwidth

are used. In this case, the second-order terms are usually

distanced in frequency from the original sine waves while the

third order terms are usually at a frequency close to the input

frequencies. As a result, the second- and third-order terms are

specified separately. Like THD, intermodulation distortion is

calculated as the rms sum of the individual distortion products

to the rms amplitude of the sum of the fundamentals, expressed

in dBs.

Rev. B | Page 11 of 24

Share Link: