ADP3330(RevC) データシートの表示（PDF） - Analog Devices

部品番号

コンポーネント説明

メーカー

ADP3330
(Rev.:RevC)

High Accuracy, Ultralow IQ, 200 mA, SOT-23, anyCAP Low Dropout Regulator

Analog Devices 

Data Sheet

APPLICATIONS INFORMATION

CAPACITOR SELECTION

Output Capacitors

As with any micropower device, output transient response is a

function of the output capacitance. The ADP3330 is stable with

a wide range of capacitor values, types, and ESR (anyCAP). A

capacitor as low as 0.47 µF is all that is needed for stability;

larger capacitors can be used if high output current surges are

anticipated. The ADP3330 is stable with extremely low ESR

capacitors (ESR ≈ 0), such as MLCC or OSCON. Note that the

effective capacitance of some capacitor types may fall less than

the minimum at cold temperature. Ensure that the capacitor

provides more than 0.47 µF at minimum temperature.

Input Bypass Capacitor

An input bypass capacitor is not strictly required, but it is

advisable in any application involving long input wires or high

source impedance. Connecting a 0.47 µF capacitor from IN to

GND reduces the sensitivity of the circuit to printed circuit

board (PCB) layout. If a larger value output capacitor is used, a

larger value input capacitor is also recommended.

NOISE REDUCTION

A noise reduction capacitor (CNR) can be used to further reduce

the noise by 6 dB to 10 dB (see Figure 23). Low leakage

capacitors in the 10 pF to 500 pF range provide the best

performance. Carefully connect to this node to avoid noise

pickup from external sources because the noise reduction pin

(NR) is internally connected to a high impedance node. The

pad connected to this pin must be as small as possible and long

PCB traces are not recommended.

When adding a noise reduction capacitor, use the following

guidelines:

• Maintain a minimum load current of 1 mA when not in

shutdown.

• For CNR values greater than 500 pF, add a 100 kΩ series

resistor (RNR).

It is important to note that as CNR increases, the turn on time is

delayed. When CNR values are greater than 1 nF, this delay may

be in the order of several milliseconds.

VIN

C1 +

0.47µF –

NR

ADP3330-3

IN

OUT

ERR

SD GND

CNR

RNR

VOUT = 3.3V

R1

330kΩ

+

–

C2

0.47µF

Figure 23. Noise Reduction Circuit

ADP3330

CHIP-ON-LEAD PACKAGE

The ADP3330 uses a Chip-on-Lead package design (protected

by U.S. Patent 5929514 A) to ensure the best thermal performance

in the 6-lead SOT-23 footprint. In a standard 6-lead SOT-23

package, the majority of the heat flows out of the ground pin.

The Chip-on-Lead package uses an electrically isolated die

attachment that allows all pins to contribute to the heat

conduction. This technique reduces the thermal resistance to

190°C/W on a 2-layer board as compared to >230°C/W for a

standard SOT-23 lead frame. Figure 24 and Figure 25 show the

difference between the standard 6-lead SOT-23 and the Chip-on-

Lead lead frames.

SILICON

DIE

Figure 24. Normal 6-Lead SOT-23 Package

SILICON DIE WITH

ELECTRICALLY

ISOLATED

DIE ATTACH

Figure 25. Thermally Enhanced, Chip-on-Lead Package

THERMAL OVERLOAD PROTECTION

The ADP3330 is protected against damage due to excessive

power dissipation by its thermal overload protection circuit,

which limits the die temperature to a maximum of 165°C.

Under extreme conditions, (that is, high ambient temperature

and power dissipation) where die temperature starts to rise

more than 165°C, the output current decreases until the die

temperature has dropped to a safe level. The output current is

restored when the die temperature is reduced.

Current and thermal limit protections protect the device against

accidental overload conditions. For normal operation, device

power dissipation must be externally limited so that the

junction temperatures do not exceed 125°C.

Rev. C | Page 11 of 16

Share Link: