HI7106 データシートの表示（PDF） - Intersil
部品番号
コンポーネント説明
メーカー
HI7106 Datasheet PDF : 11 Pages
| |||
HI7106
Absolute Maximum Ratings
Supply Voltage
HI7106, V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V
Analog Input Voltage (Either Input) (Note 1). . . . . . . . . . . . . V+ to V-
Reference Input Voltage (Either Input) . . . . . . . . . . . . . . . . . V+ to V-
Clock Input
HI7106 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TEST to V+
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . .0oC to 70oC
Thermal Information
Thermal Resistance (Typical, Note 2)
θJA (oC/W)
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
MQFP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC
Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC
(MQFP - Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Input voltages may exceed the supply voltages provided the input current is limited to ±100µA.
2. θJA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications (Note 3)
PARAMETER
TEST CONDITIONS
MIN TYP MAX
UNIT
SYSTEM PERFORMANCE
Zero Input Reading
VIN = 0.0V, Full Scale = 200mV
-000.0 ±000.0 +000.0 Digital
Reading
Stability (Last Digit)
Fixed Input Voltage (Note 6)
-000.1 ±000.0 +000.1 Digital
Reading
Ratiometric Reading
VlN = VREF, VREF = 100mV
999 999/10 1000
00
Digital
Reading
Rollover Error
-VIN = +VlN ≅ 200mV
Difference in Reading for Equal Positive and
Negative Inputs Near Full Scale
-
±0.2
±1
Counts
Linearity
Full Scale = 200mV or Full Scale = 2V Maximum -
Deviation from Best Straight Line Fit (Note 6)
±0.2
±1
Counts
Common Mode Rejection Ratio
Noise
VCM = 1V, VIN = 0V, Full Scale = 200mV (Note 6)
-
50
-
VIN = 0V, Full Scale = 200mV
-
15
-
(Peak-To-Peak Value Not Exceeded 95% of Time)
µV/V
µV
Leakage Current Input
Zero Reading Drift
Scale Factor Temperature Coefficient
VlN = 0 (Note 6)
VlN = 0, 0oC To 70oC (Note 6)
VIN = 199mV, 0oC To 70oC,
(Ext. Ref. 0ppm/oC) (Note 6)
-
1
10
pA
-
0.2
1
µV/oC
-
1
5
ppm/oC
End Power Supply Character V+ Supply
Current
VIN = 0
-
0.6
1.8
mA
COMMON Pin Analog Common Voltage
25kΩ Between Common and
Positive Supply (With Respect to + Supply)
Temperature Coefficient of Analog Common 25kΩ Between Common and
Positive Supply (With Respect to + Supply)
2.4
2.8
3.2
V
-
80
-
ppm/oC
DISPLAY DRIVER
Peak-To-Peak Segment Drive Voltage
Peak-To-Peak Backplane Drive Voltage
V+ = to V- = 9V (Note 5)
4
5
6
V
NOTES:
3. Dissipation rating assumes device is mounted with all leads soldered to printed circuit board.
4. Unless otherwise noted, specifications apply to both the HI7106 and ICL7107 at TA = 25oC, fCLOCK = 48kHz. HI7106 is tested in the
circuit of Figure 1.
5. Back plane drive is in phase with segment drive for ‘off’ segment, 180 degrees out of phase for ‘on’ segment. Frequency is 20 times
conversion rate. Average DC component is less than 50mV.
6. Not tested, guaranteed by design.
2
Share Link: 