ATA6630 データシートの表示（PDF） - Atmel Corporation

部品番号

コンポーネント説明

メーカー

ATA6630

LIN Bus Transceiver with 3.3V (5V) Regulator and Watchdog

Atmel Corporation 

3.9 Output Pin (RXD)

This output pin reports the state of the LIN-bus to the microcontroller. LIN high (recessive state) is reported by a high level at

RXD; LIN low (dominant state) is reported by a low level at RXD. The output has an internal pull-up resistor with typically

5kΩ to PVCC. The AC characteristics can be defined with an external load capacitor of 20pF.

The output is short-circuit protected. RXD is switched off in Unpowered Mode (i.e., VS = 0V).

During Fail-safe Mode it is signalling the fail-safe source.

3.10

Enable Input Pin (EN)

The Enable Input pin controls the operation mode of the device. If EN is high, the circuit is in Normal Mode, with transmission

paths from TXD to LIN and from LIN to RXD both active. The VCC voltage regulator operates with 3.3V/5V/85mA output

capability.

If EN is switched to low while TXD is still high, the device is forced to Silent Mode. No data transmission is then possible, and

the current consumption is reduced to IVS typ. 35µA. The VCC regulator has its full functionality.

If EN is switched to low while TXD is low, the device is forced to Sleep Mode. No data transmission is possible, and the

voltage regulator is switched off.

3.11

Wake Input Pin (WAKE)

The WAKE Input pin is a high-voltage input used to wake up the device from Sleep Mode or Silent Mode. It is usually

connected to an external switch in the application to generate a local wake-up. A pull-up current source, typically 10µA, is

implemented.

If a local wake-up is not needed in the application, connect the WAKE pin directly to the VS pin.

3.12

Mode Input Pin (MODE)

Connect the MODE pin directly or via an external resistor to GND for normal watchdog operation. To debug the software of

the connected microcontroller, connect MODE pin to PVCC and the watchdog is switched off.

Note:

If you do not use the watchdog, connect pin MODE directly to PVCC.

3.13

TM Input Pin

The TM pin is used for final production measurements at Atmel®. In all applications, it has to be connected to GND.

3.14

KL_15 Pin

The KL_15 pin is a high-voltage input used to wake up the device from Sleep or Silent Mode. It is an edge-sensitive pin (low-

to-high transition). It is usually connected to ignition to generate a local wake-up in the application when the ignition is

switched on. Although KL_15 pin is at high voltage (VBatt), it is possible to switch the IC into Sleep or Silent Mode. Connect

the KL_15 pin directly to GND if you do not need it. A debounce timer with a typical TdbKl_15 of 160µs is implemented.

The input voltage threshold can be adjusted by varying the external resistor due to the input current IKL_15. To protect this pin

against voltage transients, a serial resistor of 47kΩ and a ceramic capacitor of 100nF are recommended. With this RC

combination you can increase the wake-up time TwKL_15 and, therefore, the sensitivity against transients on the ignition

KL_15.

You can also increase the wake-up time using external capacitors with higher values.

3.15

INH Output Pin

The INH Output pin is used to switch an external voltage regulator on during Normal and Fail-safe Mode. The INH Output is

a high-side switch, which is switched-off in Sleep and Silent Mode. It is possible to switch off the external 1kΩ master resistor

via the INH pin for master node applications.

3.16

Reset Output Pin (NRES)

The Reset Output pin, an open drain output, switches to low during VCC undervoltage or a watchdog failure.

ATA6628/ATA6630 [DATASHEET]

5

9117I–AUTO–10/14

Share Link: