ATMEGA329PA データシートの表示（PDF） - Atmel Corporation

部品番号

コンポーネント説明

メーカー

ATMEGA329PA

8-bit Atmel Microcontroller with 16/32/64KB In-System Programmable Flash

Atmel Corporation 

2.3.8

Port E also serves the functions of various special features of the

ATmega169A/169PA/329A/329PA/3290A/3290PA/649A/649P/6490A/6490P as listed on page 80.

Port F (PF7...PF0)

2.3.9

Port F serves as the analog inputs to the A/D Converter.

Port F also serves as an 8-bit bi-directional I/O port, if the A/D Converter is not used. Port pins can provide internal

pull-up resistors (selected for each bit). The Port F output buffers have symmetrical drive characteristics with both

high sink and source capability. As inputs, Port F pins that are externally pulled low will source current if the pull-up

resistors are activated. The Port F pins are tri-stated when a reset condition becomes active, even if the clock is not

running. If the JTAG interface is enabled, the pull-up resistors on pins PF7(TDI), PF5(TMS), and PF4(TCK) will be

activated even if a reset occurs.

Port F also serves the functions of the JTAG interface.

Port G (PG5...PG0)

Port G is a 6-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port G output buf-

fers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port G pins that are

externally pulled low will source current if the pull-up resistors are activated. The Port G pins are tri-stated when a

reset condition becomes active, even if the clock is not running.

Port G also serves the functions of various special features of the

ATmega169A/169PA/329A/329PA/3290A/3290PA/649A/649P/6490A/6490P as listed on page 84.

2.3.10 Port H (PH7...PH0)

Port H is a 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port H output buf-

fers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port H pins that are

externally pulled low will source current if the pull-up resistors are activated. The Port H pins are tri-stated when a

reset condition becomes active, even if the clock is not running.

Port H also serves the functions of various special features of the ATmega3290PA/6490P as listed on page 86.

2.3.11 Port J (PJ6...PJ0)

Port J is a 7-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port J output buffers

have symmetrical drive characteristics with both high sink and source capability. As inputs, Port J pins that are

externally pulled low will source current if the pull-up resistors are activated. The Port J pins are tri-stated when a

reset condition becomes active, even if the clock is not running.

Port J also serves the functions of various special features of the ATmega3290PA/6490P as listed on page 88.

2.3.12 RESET

Reset input. A low level on this pin for longer than the minimum pulse length will generate a reset, even if the clock

is not running. The minimum pulse length is given in ”System and reset characteristics” on page 334. Shorter

pulses are not guaranteed to generate a reset.

2.3.13 XTAL1

Input to the inverting Oscillator amplifier and input to the internal clock operating circuit.

2.3.14 XTAL2

Output from the inverting Oscillator amplifier.

ATmega169A/PA/329A/PA/649A/P/3290A/PA/6490A/P [SUMMARY]

9

8284ES–AVR–02/2013

Share Link: