CA3252 データシートの表示（PDF） - Intersil
部品番号
コンポーネント説明
メーカー
CA3252 Datasheet PDF : 6 Pages
| |||
CA3252
Absolute Maximum Ratings
Output Voltage, VCEX. . . . . . . . . . . . . . . . . . . . . . . . . -0.7 to 50VDC
Logic Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Logic Input Voltage, VIN . . . . . . . . . . . . . . . . . . . . . . . . . .-0.7 to 15V
Output Sustaining Voltage, VCE(SUS) . . . . . . . . . . . . . . . . . . 35VDC
Output Current, IO (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . 1ADC
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 105oC
Thermal Information
Thermal Resistance (Typical, Note 2)
θJAoC/W
CA3252E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45
CA3252M. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
54
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC
Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC
Maximum Lead Temperature Soldering (10s Max) . . . . . . . . . 300oC
(SOIC - Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. The Maximum Ambient Temperature is limited for the sustained conditions of the ICC(ON) Supply Current test with all Outputs ON. The total
DC current for the CA3252 with all 4 outputs ON should not exceed 0.7A at each output for a total of (4 X 0.7A + Max. ICC) ~ 2.9A. This
level of sustained current will significantly increase the on-chip temperature due to increased dissipation. Under any condition, the Absolute
Maximum Junction Temperature must not exceed150oC. While any one loaded output may exceed 0.7A, the maximum rating limit is 1A.
2. θJA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications TA = -40oC to 105oC, VCC = VEN = 5V; Unless Otherwise Specified
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
MAX
UNITS
Output Sustaining Voltage
Output Leakage Current
Collector to Emitter Saturation Voltage
Input Low Voltage
Input Low Current
Input High Voltage
Input High Current
Logic Supply Current, All Outputs ON
Logic Supply Current, All Outputs OFF
Clamp Diode Leakage Current
Clamp Diode Forward Voltage
Output Current
VCE(SUS)
ICEX
VCE(SAT)
VIL
IIL
VIH
IIH
ICC(ON)
ICC(OFF)
IR
VF
IOUT
IC = 100mA, VIN = 2V, VEN = 2V
VCE = 50V, VIN = 2V, VEN = 0.8V
IC = 100mA, VIN = 0.8V
IC = 300mA, VIN = 0.8V
IC = 600mA, VIN = 0.8V
VIN = 0.4V
IC = 600mA
IC = 600mA, VIN = 4.5V
IC = 600mA, All Outputs ON (Note 1)
All Outputs OFF
VR = 50V (Diode Reverse Voltage)
IF = 0.6A
IF = 1.2A
VIN = 0.4V, VBATT = +13V,
Output Load = 10Ω
35
-
V
-
100
µA
-
0.3
V
-
0.5
V
-
0.8
V
-
0.8
V
-15
10
µA
2
-
V
-10
-10
µA
-
90
mA
-
10
mA
-
100
µA
-
1.8
V
-
2.0
V
0.9
-
A
Turn-ON Propagation Delay Time
Turn-OFF Propagation Delay Time
Low Enable Voltage
Low Enable Current
High Enable Voltage
High Enable Current
tPHL
tPLH
VENL
IENL
VENH
IENH
IC = 600mA
IC = 600mA
VEN = 0.4V
VEN ≥ 2V
-
10
µs
-
10
µs
-
0.8
V
-15
10
µA
2.0
-
V
-250
+250
µA
4
Share Link: 