CS61577-IL1Z データシートの表示（PDF） - Cirrus Logic
部品番号
コンポーネント説明
メーカー
CS61577-IL1Z Datasheet PDF : 30 Pages
| |||
CS61577
#3
Transmitter
The transmitter takes digital T1 or E1 input data
and drives appropriately shaped bipolar pulses
onto a transmission line through a 1:2 trans-
former. The transmit data (TPOS & TNEG or
TDATA) is supplied synchronously and sampled
on the falling edge of the input clock, TCLK.
Either T1 (DSX-1 or Network Interface) or E1
CCITT G.703 pulse shapes may be selected.
Pulse shaping and signal level are controlled by
"line length select" inputs as shown in Table 3.
For T1 DSX-1 applications, line lengths from 0 to
655 feet (as measured from the transmitter to the
DSX-1 cross connect) may be selected. The five
partition arrangement in Table 3 meets ANSI
T1.102 and AT&T CB-119 requirements when
using #22 ABAM cable. A typical output pulse is
shown in Figure 8. These pulse settings can also
be used to meet CCITT pulse shape requirements
for 1.544 MHz operation.
For T1 Network Interface applications, two addi-
tional options are provided. Note that the optimal
pulse width for Part 68 (324 ns) is narrower than
the optimal pulse width for DSX-1 (350 ns). The
CS61577 automatically adjusts the pulse width
based upon the "line length" selection made.
,%. ,%. ,%. /PTION 3ELECTED !PPLICATION
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
0-133 FEET
133-266 FEET
266-399 FEET
399-533 FEET
533-655 FEET
DSX-1
ABAM
(AT&T 600B
or 600C)
0
0
0
75 Ω (with 4.4 Ω
resistor) & 120 Ω
E1
0
0
1
75 Ω (without
CCITT G.703
4.4 Ω resistor)
0
1
0 FCC PART 68, OPT. A NETWORK
0
1
1
ANSI T1.403
INTERFACE
Table 3. Line Length Selection
NORMALIZED
AMPLITUDE
1.0
0.5
ANSI T1.102,
AT&T CB 119
SPECIFICATIONS
0
OUTPUT
PULSE SHAPE
-0.5
0
250
500
750
1000
TIME (nanoseconds)
Figure 8. Typical Pulse Shape at DSX-1 Cross Connect
The E1 G.703 pulse shape is supported with line
length selections LEN2/1/0=0/0/0 or
LEN2/1/0=0/0/1. As with the CS61574,
LEN2/1/0=0/0/0 supports the 120 Ω, 3 V output
option without external series resistors, but will
also support the 75 Ω, 2.37 V output option with
an external 4.4 Ω resistor in series with TTIP or
TRING. The new LEN2/1/0=0/0/1 code supports
the 75 Ω, 2.37 V output option without external
series resistors allowing for software selection be-
tween the two E1 output options. The pulse width
will meet the G.703 pulse shape template shown
in Figure 9, and specified in Table 4.
The CS61577 will detect a static TCLK, and will
force TTIP and TRING low to prevent transmis-
sion when data is not present. When any transmit
control pin (TAOS, LEN0-2 or LLOOP) is tog-
gled, the transmitter outputs will require
approximately 22 bit periods to stabilize. The
transmitter will take longer to stabilize when
RLOOP is selected because the timing circuitry
must adjust to the new frequency.
10
$3DS15050F
Share Link: 