CY14B101L-SZ25XC データシートの表示（PDF） - Cypress Semiconductor
部品番号
コンポーネント説明
メーカー
CY14B101L-SZ25XC Datasheet PDF : 18 Pages
| |||
CY14B101L
Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the
device. These user guidelines are not tested.
Storage Temperature ................................. –65°C to +150°C
Ambient Temperature with
Power Applied ............................................ –55°C to +125°C
Supply Voltage on VCC Relative to GND ..........–0.5V to 4.1V
Voltage Applied to Outputs
in High Z State ....................................... –0.5V to VCC + 0.5V
Input Voltage...........................................–0.5V to Vcc + 0.5V
Transient Voltage (<20 ns) on
Any Pin to Ground Potential .................. –2.0V to VCC + 2.0V
Package Power Dissipation
Capability (TA = 25°C) ................................................... 1.0W
Surface Mount Lead Soldering
Temperature (3 Seconds) .......................................... +260°C
DC output Current (1 output at a time, 1s duration) .... 15 mA
Static Discharge Voltage.......................................... > 2001V
(MIL-STD-883, Method 3015)
Latch Up Current ................................................... > 200 mA
Operating Range
Range
Commercial
Industrial
Ambient Temperature
0°C to +70°C
-40°C to +85°C
VCC
2.7V to 3.6V
2.7V to 3.6V
DC Electrical Characteristics
Over the operating range (VCC = 2.7V to 3.6V) [4, 5]
Parameter
Description
Test Conditions
ICC1
Average VCC Current tRC = 25 ns
tRC = 35 ns
tRC = 45 ns
Dependent on output loading and cycle rate.
Values obtained without output loads.
IOUT = 0 mA.
Commercial
Industrial
Min
Max Unit
65 mA
55 mA
50
70 mA
60 mA
55 mA
ICC2
ICC3
ICC4
ISB
IIX
IOZ
VIH
VIL
VOH
VOL
VCAP
Average VCC Current All Inputs Do Not Care, VCC = Max
during STORE
Average current for duration tSTORE
Average VCC Current at WE > (VCC – 0.2V). All other inputs cycling.
tRC= 200 ns, 5V, 25°C Dependent on output loading and cycle rate. Values obtained
Typical
without output loads.
Average VCAP Current All Inputs Do Not Care, VCC = Max
during AutoStore Cycle Average current for duration tSTORE
VCC Standby Current
CE > (VCC – 0.2V). All others VIN < 0.2V or > (VCC – 0.2V).
Standby current level after nonvolatile cycle is complete.
Inputs are static. f = 0 MHz.
Input Leakage Current VCC = Max, VSS < VIN < VCC
Off State Output
Leakage Current
VCC = Max, VSS < VIN < VCC, CE or OE > VIH or WE < VIL
Input HIGH Voltage
Input LOW Voltage
Output HIGH Voltage
Output LOW Voltage
Storage Capacitor
IOUT = –2 mA
IOUT = 4 mA
Between VCAP pin and Vss, 6V rated.
6
mA
10 mA
3
mA
3
mA
-1
+1 μA
-1
+1 μA
2.0
VCC + V
0.5
VSS – 0.5 0.8
V
2.4
V
0.4
V
17
120 uF
Notes
4. The HSB pin has IOUT = –10 μA for VOH of 2.4 V. This parameter is characterized but not tested.
5. VIH changes by 100 mV when VCC > 3.5V.
Document Number: 001-06400 Rev. *J
Page 7 of 18
[+] Feedback
Share Link: 