LTC1287_1 データシートの表示（PDF） - Linear Technology
部品番号
コンポーネント説明
メーカー
LTC1287_1 Datasheet PDF : 16 Pages
| |||
LTC1287
TYPICAL PERFOR A CE CHARACTERISTICS
Maximum Clock Rate vs Source
Resistance
500
VCC = 3V
VREF = 2.5V
400
CLK = 500kHz
300
200
+VIN +IN
100 RSOURCE–
–IN
Minimum Clock Rate for 0.1LSB
Error**
VCC = 3V
0.25
0.20
0.15
0.10
0.05
Maximum Filter Resistor vs Cycle
Time
10k
RFILTER
VIN
+
1k
CFILTER ≥1µF
–
100
10
0
100
1k
10k
RSOURCE– (Ω)
100k
LTC G10
1
–50 –25 0 25 50 75 100
10
AMBIENT TEMPERATURE (°C)
LTC1287 G11
100
1000
CYCLE TIME (µs)
10000
LTC1287 G12
Sample-and-Hold Acquisition
Time vs Source Resistance
100
VREF = 2.5V
VCC = 3V
TA = 25°C
0V TO 2.5V INPUT STEP
10
+ RSOURCE+
VIN
–
Input Channel Leakage Current vs
Temperature
1000
900
GUARANTEED
800
700
600
500
400
300
200
ON CHANNEL
100
OFF CHANNEL
Noise Error vs Reference Voltage
1.0
0.9 LTC1287 NOISE = 200µVP-P
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
1
0
0
100
1k
10k
–50 –30 –10 10 30 50 70 90 110 130
0 0.5 1.0 1.5 2.0 2.5 3.0
RSOURCE+ (Ω)
AMBIENT TEMPERATURE (°C)
REFERENCE VOLTAGE (V)
LTC1287 G13
* MAXIMUM CLK FREQUENCY REPRESENTS THE CLK FREQUENCY AT WHICH A 0.1LSB
SHIFT IN THE ERROR AT ANY CODE TRANSITION FROM ITS 500kHz VALUE IS FIRST DETECTED.
** AS THE CLK FREQUENCY IS DECREASED FROM 1MHz, MINIMUM CLK FREQUENCY
(∆ERROR ≤ 0.1LSB) REPRESENTS THE FREQUENCY AT WHICH A 0.1LSB SHIFT IN ANY
CODE TRANSITION FROM ITS 500kHz VALUE IS FIRST DETECTED.
LTC1287 G14
LTC1287 G15
*** MAXIMUM RFILTER REPRESENTS THE FILTER RESISTOR VALUE AT WHICH A 0.1LSB
CHANGE IN FULL SCALE ERROR FROM ITS VALUE AT RFILTER = 0Ω IS FIRST DETECTED.
PI FU CTIO S
CS (Pin 1): Chip Select Input. A logic low on this input
enables the LTC1287.
+IN, –IN (Pin 2,3): Analog Inputs. These inputs must be
free of noise with respect to GND.
GND (Pin 4): Analog Ground GND should be tied directly
to an analog ground plane.
VREF (Pin 5): Reference Input. The reference input defines
the span of the A/D converter and must be kept free of
noise with respect to GND.
DOUT (Pin 6): Digital Data Output. The A/D conversion
result is shifted out of this output.
CLK (Pin 7): Shift Clock. This clock synchronizes the serial
data transfer.
VCC (Pin 8): Positive Supply. This supply must be kept free
of noise and ripple by bypassing directly to the analog
ground plane.
1287fa
5
Share Link: 