EL5178IY-T7 データシートの表示（PDF） - Intersil
部品番号
コンポーネント説明
メーカー
EL5178IY-T7 Datasheet PDF : 15 Pages
| |||
EL5178, EL5378
The gain setting for EL5378 is:
VODM
=
(
VIN
+
–
VI
N
-
)
×
1
+
-R----F----1-R---+--G---R-----F---2-
VODM
=
(
VIN
+
–
VI
N
-
)
×
1
+
-2---R-----F-
RG
VOCM = VREF
Where:
RF1 = RF2 = RF
RF1
VIN+
RG
VIN-
VREF
FBP
IN+
IN-
REF
FBN
RF2
VO+
VO-
FIGURE 23.
Choice of Feedback Resistor and Gain Bandwidth
Product
For gains greater than 1, the feedback resistor forms a pole
with the parasitic capacitance at the inverting input. As this
pole becomes smaller, the amplifier's phase margin is
reduced. This causes ringing in the time domain and
peaking in the frequency domain. Therefore, RF has some
maximum value that should not be exceeded for optimum
performance. If a large value of RF must be used, a small
capacitor in the few Pico farad range in parallel with RF can
help to reduce the ringing and peaking at the expense of
reducing the bandwidth.
The bandwidth of the EL5178 and EL5378 depends on the
load and the feedback network. RF and RG appear in
parallel with the load for gains other than 1. As this
combination gets smaller, the bandwidth falls off.
Consequently, RF also has a minimum value that should not
be exceeded for optimum bandwidth performance. For the
gains other than 1, optimum response is obtained with RF
between 500Ω to 1kΩ.
The EL5178 and EL5378 have a gain bandwidth product of
350MHz for RLD = 1kΩ. For gains ≥5, its bandwidth can be
predicted by the following equation:
Gain × BW = 300MHz
Driving Capacitive Loads and Cables
The EL5178 and EL5378 can drive 23pF differential
capacitor in parallel with 200Ω differential load with less than
5dB of peaking at gain of 2. If less peaking is desired in
applications, a small series resistor (usually between 5Ω to
50Ω) can be placed in series with each output to eliminate
most peaking. However, this will reduce the gain slightly. If
the gain setting is greater than 2, the gain resistor RG can
then be chosen to make up for any gain loss which may be
created by the additional series resistor at the output.
When used as a cable driver, double termination is always
recommended for reflection-free performance. For those
applications, a back-termination series resistor at the
amplifier's output will isolate the amplifier from the cable and
allow extensive capacitive drive. However, other applications
may have high capacitive loads without a back-termination
resistor. Again, a small series resistor at the output can help
to reduce peaking.
Disable/Power-Down (for EL5378 only)
The EL5378 can be disabled and placed its outputs in a high
impedance state. The turn off time is about 1.2µs and the
turn on time is about 130ns. When disabled, the amplifier's
supply current is reduced to 1.7µA for IS+ and 120µA for IS-
typically, thereby effectively eliminating the power
consumption. The amplifier's power down can be controlled
by standard CMOS signal levels at the EN pin. The applied
logic signal is relative to VS+ pin. Letting the EN pin float or
applying a signal that is less than 1.5V below VS+ will enable
the amplifier. The amplifier will be disabled when the signal
at EN pin is above VS+ - 0.5V.
Output Drive Capability
The EL5178 and EL5378 have internal short circuit
protection. Its typical short circuit current is ±60mA. If the
output is shorted indefinitely, the power dissipation could
easily increase such that the part will be destroyed.
Maximum reliability is maintained if the output current never
exceeds ±60mA. This limit is set by the design of the internal
metal interconnections.
Power Dissipation
With the high output drive capability of the EL5178 and
EL5378. It is possible to exceed the 135°C absolute
maximum junction temperature under certain load current
conditions. Therefore, it is important to calculate the
maximum junction temperature for the application to
determine if the load conditions or package types need to be
modified for the amplifier to remain in the safe operating
area.
The maximum power dissipation allowed in a package is
determined according to:
PDMAX
=
T----J---M-----A----X-----–-----T----A---M-----A----X--
ΘJA
11
FN7491.1
March 8, 2005
Share Link: 