HIP0082 データシートの表示（PDF） - Intersil
部品番号
コンポーネント説明
メーカー
HIP0082 Datasheet PDF : 12 Pages
| |||
HIP0082, HIP0084
Absolute Maximum Ratings TA = 25oC
Supply Voltage (Logic and Control), VCC . . . . . . . . . . . . -0.3V to 7V
Power MOSFET Drain Voltage, VO (Note 3) . . . . . . -0.7 to VCLAMP
Output Clamp Energy, EOK (See Note 5). . . . . . . . . . . . . . . . . 70mJ
Input Voltage (Logic and Driver Inputs), VIN. . . .-0.5V to VCC +0.5V
Maximum Output Current, Outputs 1 and 2 . . . . . . . . . . . . . . . . +2A
Maximum Output Current, Outputs 3 and 4 . . . . . . . . . . . . . . . . +5A
Maximum Total Output Current, All Outputs ON. . . . . . . . . . . . . +8A
Maximum Peak Output Current, IO(MAX), (Note 4) . . . . . -5A to ISC
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 125oC
Thermal Information
Thermal Resistance (Typical, Notes 5, 6, 7) θJA (oC/W) θJC (oC/W)
Power SIP Package . . . . . . . . . . . . . . .
45
3
PSOP Package . . . . . . . . . . . . . . . . . .
40
2
Maximum Junction Temperature . . . . . . . . . . . . . . . -40oC to 150oC
Maximum Storage Temperature Range, TSTG . . . . -55oC to 150oC
Maximum Lead Temperature (During Soldering 10s) . . . . . . 300oC
(PSOP - Lead Tips Only)
Die Characteristics
Back Side Potential . . . . . . . . . . . . . . . . . . . . . . . .VSS (Tab Ground)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
3. The MOSFET Output Drain is internally clamped with a Drain-to-Gate zener diode that turns on the MOSFET to hold the Drain at the
VCLAMP voltage. Refer to the Electrical Specifications Table for the VCLAMP voltage limits.
4. Each Output has Over Current Shutdown protection in the positive current direction. The maximum peak current rating is set equal to the
minimum Over Current Shutdown as detailed in the Electrical Specification Table. In the event of an Over Current Shutdown the input
drive is latched OFF. The output short must be removed and the input toggled OFF and ON to restore the output drive.
5. Refer to Application Note AN9416 for Single Pulse Energy and Device Dissipation rating information, including inductive load operation
and other thermal stress characterization.
6. θJA is measured with the component mounted on an evaluation PC board in free air.
7. Maximum PSOP Package Dissipation at 125oC with 26oC/W Heat Sink (6 sq cm Copper PCB) is 0.96W.
Electrical Specifications VCC = 5V ±10%, TA = -40oC to 125oC; Unless Otherwise Specified
HIP0082
HIP0084
PARAMETER
SYMBOL
TEST CONDITIONS
MIN TYP MAX MIN TYP MAX UNITS
POWER OUTPUTS
Output ON Resistance
(Normal Mode)
Output ON Resistance
(Normal Mode)
rDS(ON)1,
rDS(ON)2
Outputs 1 and 2, One Output ON,
IOUT = 2A, TJ = 150oC
-
rDS(ON)3, Outputs 3 and 4, One Output ON, -
rDS(ON)4 IOUT = 2A, TJ = 150oC
rDS(ON)1,
rDS(ON)2
Outputs 1 and 2, One Output ON,
IOUT = 2A, TJ = 75oC
Output ON Resistance
(Normal Mode)
rDS(ON)3,
rDS(ON)4
Outputs 3 and 4, One Output ON,
IOUT = 2A, TJ = 105oC
Output Zener Clamp Voltage
VZ
IOUT = 40mA
73
Matching Zener Clamp
Voltage
∆VZ IOUT = 40mA, tZ = 100µs
-
0.62 -
-
0.57 -
-
N/A
-
80
90 73
N/A
-
-
0.62
Ω
-
0.57
Ω
-
0.5
Ω
-
0.5
Ω
80
90
V
-
±1.5
V
Output Short Current Limit,
Outputs 1 and 2 (Note 8)
ISC(L)
2
-
3.4 3
-
5.1
A
Output Short Current Limit,
Outputs 3 and 4 (Note 8)
ISC(L) ISC Bit High
2
-
3.4 2
-
3.4
A
Output Short Current Limit,
Outputs 3 and 4 (Note 8)
ISC(H) ISC Bit Low
5
-
7.5 5
-
8.3
A
Short Circuit Current Filter
tSC
Time
-
-
1
-
-
3
µs
Output Capacitance
CO VOUTX = 16V, f = 1MHz
-
-
250 -
-
250 pF
3
Share Link: 