HIP1013(1999) データシートの表示（PDF） - Intersil
部品番号
コンポーネント説明
メーカー
HIP1013 Datasheet PDF : 7 Pages
| |||
HIP1013
Absolute Maximum Ratings TA = 25oC
VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +13.2V
3/12VG, CPUMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 18.5V
3/12VISEN, 3/12VS . . . . . . . . . . . . . . . . . . . . . . . -5V to VDD + 0.3V
5VISEN, 5VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -5V to 7.5V
PGOOD, RILIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 7.5V
MODE/PWRON1, PWRON2, 5VG . . . . . . . . . .-0.3V to VDD + 0.3V
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2kV (Class 2)
Thermal Information
Thermal Resistance (Typical, Note 1)
θJA (oC/W)
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
120
Maximum Junction Temperature (Plastic Package) . . . . . . . .150oC
Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC
(SOIC - Lead Tips Only)
Operating Conditions
VDD Supply Voltage
Temperature Range
Range
(TA) . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
+10.5V to +13.2V
. . . . 0oC to 70oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. θJA is measured with the component mounted on an evaluation PC board in free air.
2. All voltages are relative to GND, unless otherwise specified.
Electrical Specifications VDD = 12V, CVG = 0.01µF, RSENSE = 0.1Ω, CBULK = 220µF, ESR = 0.5Ω, TA = TJ = 0oC to 70oC, Unless
Otherwise Specified
PARAMETER
SYMBOL
TEST CONDITIONS
MIN TYP MAX UNITS
CONTROL SECTION
Current Limit Threshold Voltage
(Voltage Across Sense Resistor)
VIL
RILIM = 10kΩ
85
100
115
mV
Over Current Limit Response Time
Response Time To Dead Short
12V Gate Turn-On Time
5V Gate Turn-On Time
Gate Turn-On Current
12V Under Voltage Threshold
5V Under Voltage Threshold
3.3V Under Voltage Threshold
Charge pumped 12VG Voltage
3/5VG High Voltage
OCLrt Current Overload, RILIM = 10kΩ, RSHORT = 6.0Ω
-
2
-
µs
RTSHORT CVG = 0.01µF
-
500 1000
ns
tON12V CVG = 0.01µF
-
12
-
ms
tON5V CVG = 0.01µF
-
5
-
ms
ION
CVG = 0.01µF
8
10
12
µA
12VVUV
10.5 10.8 11.0
V
5VVUV
4.35 4.5 4.65
V
3.3VVUV
2.65 2.8 2.95
V
V12VG CPUMP = 0.1µF
16.8 17.3 17.9
V
3/5VG
11.2 11.9
-
V
SUPPLY CURRENT AND IO SPECIFICATIONS
VDD Supply Current
VDD POR Rising Threshold
VDD POR Falling Threshold
PWRON Pull-up Voltage
IVDD
PORrvth
PORfvth
PWRN_V
PWRON pins open
4
8
10
mA
9.5 10.0 10.5
V
9.3
9.8 10.3
V
1.8
2.4
3.2
V
PWRON Rising Threshold
PWR_Vth
1.1
1.5
2
V
PWRON Hysteresis
PWR_hys
0.1
0.2
0.3
V
PWRON Pull-Up Current
PWRN_I
60
80
100
µA
RILIM Pin Current Source Output
Charge Pump Output Current
Charge Pump Output Voltage
RILIM_Io
Qpmp_Io
Qpmp_Vo
CPUMP = 0.1µF, CPUMP = 16V
No load
90
100 110
µA
400 590 800
µA
17.2 17.4
-
V
Charge Pump Output Voltage - Loaded
Qpmp_VIo Load current = 100µA
16.2 16.7
-
V
Charge Pump POR Rising Threshold
Qpmp+Vth
15.6
16
16.5
V
Charge Pump POR Falling Threshold
Qpmp-Vth
15.2 15.7 16.2
V
2-409
Share Link: 