HIP0080AM(1998) データシートの表示（PDF） - Intersil

部品番号

コンポーネント説明

メーカー

HIP0080AM
(Rev.:1998)

Quad Inverting Power Drivers with Serial Diagnostic Interface

Intersil 

HIP0080, HIP0081

Electrical Specifications VCC = 5.5V to 25V ±5%, TA = -40oC to 125oC, Unless Otherwise Specified (Continued)

HIP0080

HIP0081

PARAMETER

SYMBOL

TEST CONDITIONS

MIN TYP MAX MIN TYP MAX UNITS

HIP0080 Output Leakage

Current

IOFFLK Inputs Low, Each VOUT = 25V,

ENABLE Low

-

1.0 10

-

-

-

µA

Over-Voltage Clamp Range

Current Short Circuit Prot.

Short Circuit Det. Delay

Output ON-OFF Voltage

Ramp Rate

VCLAMP IN Inputs Low (Outputs OFF),

IOUT = 40mA

IOUT(SC) Note 2

tSCDLY

Resistive Load

27

-

43 73

-

89

V

1.3

-

-

6

-

10

3 2.2

-

4.8

A

-

-

6

-

µs

-

-

10

-

V/µs

Turn-On Delay

Turn-Off Delay

SUPPLY

tPHL

tPLH

VCC = 14V, RLOAD = 14Ω

VCC = 14V, RLOAD = 14Ω

-

-

8

-

-

8

µs

-

-

8

-

-

8

µs

Power Supply Current

Power Supply Reset Active

Shut-Down Current Mode

INPUTS

ICC

VCC_RST

TA = 25oC to TA = 125oC

TA = -40oC

ISHTDN Enable Low

-

20

30

-

20

30 mA

3

-

4

3

-

4

V

2.7

-

4 2.7

-

4

V

-

130 200 -

-

-

µA

Low-Level Input Voltage

High-Level Input Voltage

Input Hysteresis Threshold

Input Pull-Down

Resistance

VIL

VIH

VIN_HYS (N.A. to HIP0080 ENABLE)

RPD IN1, IN2, IN3, IN4 and ENABLE

-

-

1

-

-

1

V

3.5

-

-

3.5

-

-

V

0.85

-

2.25 0.85

-

2.25

V

50 100 200 50 100 200 kΩ

DATAOUT (Open Drain)

Leakage Current

IDO_LEAK VDO = 7V, DO OFF (High)

Logic Low Output Voltage

VOL IDO = 1.6mA, DO ON (Low)

Max. Logic Low Current

IOH VDO = 4.5V, DO ON

Oscillator Frequency

fOSC

Serial Interface Clock Freq.

fCLK Note 5

DIAGNOSTIC AND PROTECTION

Over-Temperature

Shutdown Threshold

Shutdown Temperature Hys-

teresis

-

-

10

-

-

10

µA

-

-

0.4 -

-

0.4

V

1.6

-

-

1.6

-

-

mA

-

500

-

-

500

-

kHz

-

-

2

-

-

2 MHz

150 165

- 150 165

-

oC

-

15

-

-

15

-

oC

Output Short-to-GND

Threshold

Short-to-GND Hysteresis

Open-Load Resistance for

No-Load Warning

VCC = 5.5V to 16V

VCC = 5.5V to 16V

VCC = 5.5V to 16V

- 0.24x -

- 0.24x -

V

VCC

VCC

- 0.02x -

- 0.02x -

V

VCC

VCC

5

-

25

5

-

25

kΩ

Filter Delay Time for O.L. or

Short-to-GND

-

12

-

-

12

-

µs

NOTE:

5. The maximum Serial Clock Frequency may be limited by the time constant of the external load network at the DATAOUT pin.

5

Share Link: