HT46C48A データシートの表示（PDF） - Holtek Semiconductor

部品番号

コンポーネント説明

メーカー

HT46C48A

Cost-Effective A/D Type 8-Bit MCU

Holtek Semiconductor 

HT46R46/C46/R47/C47/R48A/C48A/R49

HT46R49

Pin Name

I/O

Configuration

Option

Description

PA0~PA2

PA3/PFD

PA4/TMR

PA5/INT

PA6~PA7

Bidirectional 8-bit input/output port. Each individual pin on this port can be config-

Pull-high ured as a wake-up input by a configuration option. Software instructions deter-

I/O Wake-up mine if the pin is a CMOS output or Schmitt Trigger input. Configuration options

PA3 or PFD determine which pins on the port have pull-high resistors. Pins PA3, PA4 and PA5

are pin-shared with PFD, TMR and INT, respectively.

PB0/AN0

PB1/AN1

PB2/AN2 I/O

PB3/AN3

PB4~PB7

Pull-high

Bidirectional 8-bit input/output port. Software instructions determine if the pin is a

CMOS output or Schmitt Trigger input. Configuration options determine which

pins on the port have pull-high resistors. PB is pin-shared with the A/D input pins.

The A/D inputs are selected via software instructions. Once selected as an A/D in-

put, the I/O function and pull-high resistor options are disabled automatically.

PC0~PC4 I/O

Pull-high

Bidirectional 5-bit input/output port. Software instructions determine if the pin is a

CMOS output or Schmitt Trigger input. Configuration options determine which

pins on the port have pull-high resistors.

PD0/PWM0

PD1/PWM1

I/O

Pull-high

I/O or PWM

Bidirectional 2-bit input/output port. Software instructions determine if the pin is a

CMOS output or Schmitt Trigger input. Configuration option determines if this pin

has a pull-high resistor. The PWM output are pin-shared with pins PD0 and PD1

selected via a configuration option.

OSC1

OSC2

OSC1, OSC2 are connected to an external RC network or external crystal, deter-

I

O

Crystal or RC

mined by configuration option, for the internal system clock. If the RC system

clock option is selected, pin OSC2 can be used to measure the system clock at

1/4 frequency.

RES

I

¾

Schmitt Trigger reset input. Active low.

VDD

¾

¾

Positive power supply

VSS

¾

¾

Negative power supply, ground

Note:

1. Each pin on PA can be programmed through a configuration option to have a wake-up function.

2. Individual pins can be selected to have a pull-high resistor.

3. Pins PC2~PC4 and pin PD1/PWM1 exist but are not bonded out on the 24-pin package.

4. Unbonded pins should be setup as outputs or as inputs with pull-high resistors to conserve power.

Absolute Maximum Ratings

Supply Voltage ...........................VSS-0.3V to VSS+6.0V

Input Voltage..............................VSS-0.3V to VDD+0.3V

IOL Total ..............................................................150mA

Total Power Dissipation .....................................500mW

Storage Temperature ............................-50°C to 125°C

Operating Temperature...........................-40°C to 85°C

IOH Total............................................................-100mA

Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may

cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed

in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.

Rev. 1.30

5

June 5, 2008

Share Link: