IDT71V016SA10PH8 データシートの表示（PDF） - Integrated Device Technology
部品番号
コンポーネント説明
メーカー
IDT71V016SA10PH8 Datasheet PDF : 9 Pages
| |||
IDT71V016SA, 3.3V CMOS Static RAM
1 Meg (64K x 16-Bit)
Commercial and Industrial Temperature Ranges
Absolute Maximum Ratings(1)
Recommended Operating
Symbol
Rating
Value
Unit Temperature and Supply Voltage
VDD
Supply Voltage Relative to –0.5 to +4.6
V
VSS
VIN, VOUT Terminal Voltage Relative –0.5 to VDD+0.5
V
to VSS
TBIAS
Temperature Under Bias
–55 to +125
oC
Grade
Commercial
Industrial
Temperature
0°C to +70°C
-40°C to +85°C
VSS
VDD
0V
See Below
0V
See Below
3834 tbl 04
TSTG
Storage Temperature
PT
Power Dissipation
–55 to +125
1.25
oC Recommended DC Operating
W Conditions
IOUT
DC Output Current
50
mA
NOTE:
3834 tbl 03
1. StressesgreaterthanthoselistedunderABSOLUTEMAXIMUMRATINGSmaycause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
Capacitance
(TA = +25°C, f = 1.0MHz, SOJ package)
Symbol
Parameter(1)
Conditions
Max. Unit
CIN Input Capacitance
VIN = 3dV
6 pF
CI/O I/O Capacitance
VOUT = 3dV
7 pF
Symbol
Parameter
VDD(1) Supply Voltage
VDD(2) Supply Voltage
Min. Typ. Max. Unit
3.15 3.3
3.6
V
3.0
3.3
3.6
V
Vss Ground
0
0
0
V
VIH Input High Voltage
VIL Input Low Voltage
2.0
–0.3(4)
____ VDD+0.3(3) V
____
0.8
V
NOTES:
1. For 71V016SA10 only.
2. For all speed grades except 71V016SA10.
3. VIH (max.) = VDD+2V for pulse width less than 5ns, once per cycle.
4. VIL (min.) = –2V for pulse width less than 5ns, once per cycle.
3834 tbl 05
NOTE:
3834 tbl 06
1. This parameter is guaranteed by device characterization, but not production tested.
DC Electrical Characteristics
(VDD = Min. to Max., Commercial and Industrial Temperature Ranges)
IDT71V016SA
Symbol
Parameter
Test Condition
|ILI|
Input Leakage Current
|ILO|
Output Leakage Current
VOL
Output Low Voltage
VDD = Max., VIN = VSS to VDD
VDD = Max., CS = VIH, VOUT = VSS to VDD
IOL = 8mA, VDD = Min.
VOH
Output High Voltage
IOH = –4mA, VDD = Min.
DC Electrical Characteristics(1,2)
(VDD = Min. to Max., VLC = 0.2V, VHC = VDD – 0.2V)
71V016SA10 71V016SA12
Min.
Max.
Unit
___
5
µA
___
5
µA
___
0.4
V
2.4
___
V
3834 tbl 07
71V016SA15 71V016SA20
Symbol
Parameter
Com'l Only Com'l Ind Com'l Ind Com'l Ind Unit
ICC Dynamic Operating Current
Max.
160
CS ≤ VLC, Outputs Open, VDD = Max., f = fMAX(3) Typ.(4)
125
150 160 130 130 120 120 mA
120
--
110
--
110
--
ISB Dynamic Standby Power Supply Current
CS ≥ VHC, Outputs Open, VDD = Max., f = fMAX(3)
45
40
45
35
35
30
30
mA
ISB1 Full Standby Power Supply Current (static)
CS ≥ VHC, Outputs Open, VDD = Max., f = 0(3)
10
10
10
10
10
10
10
mA
NOTES:
1. All values are maximum guaranteed values.
2. All inputs switch between 0.2V (Low) and VDD – 0.2V (High).
3. fMAX = 1/tRC (all address inputs are cycling at fMAX); f = 0 means no address input lines are changing .
4. Typical values are measured at 3.3V, 25°C and with equal read and write cycles.
3834 tbl 08
6.432
Share Link: 